Do the Frame Holes Need To Be Cleaned Before Installing Curt Hitch on a 2021 Honda Pilot
Question:
I watched one video prior to ordering the hitch and the technician used a lubricant and brush before ing screws into the frame so I had planned using grease on the screws prior to ing. I just watched a different video and the screws were ed without any mention of lubricant. Is there a preferred method?
asked by: Bill B
Expert Reply:
In regards to installing the Curt Trailer Hitch Receiver part # C13146 on a 2021 Honda Pilot, it will be a good idea to clean the factory weld nuts out on the bottom of the frame prior to inserting the hardware. This can be done with any general purpose aerosol lubricant and some sort of wire brush. That said, the weld nuts being dirty and not allowing the fasteners to thread is really only any issue on older vehicles.
I have attached an install video I did below as well but as this was a brand new vehicle, the holes did not need to be cleaned prior.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Tools Needed To Torque The 14MM Hitch Bolts For the Curt Receiver # C13146 On a 2020 Honda Pilot
- Shop: Torque Wrench - Dual Scale - 1/2" Drive - 250 ft/lb
- Shop: Trailer Wiring
- Video: Best 2022 Honda Pilot Trailer Hitch Options
- Video: Setting up the Curt Trailer Hitch Receiver on a 2020 Honda Pilot
- Q&A: Recommended Hitch and Weight for a 2021 Honda Pilot
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Finding the Right Trailer Wiring Harness
- Article: Trailer Wiring Diagrams
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: hitch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Article: My Trailer Hitch Doesn't Fit
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2024 Honda Pilot
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Article: How to Measure for Trailer Hitch Drop
- Search Results: brake controller
- Video: Step-By-Step Installation Tutorial for the etrailer Trailer Hitch Receiver on a 2024 Toyota RAV4
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: Gooseneck Hitch
on Trailer Hitch
