Replacement 2-Way Connectors for Winch Connection Made to Wiring

Question

Question:

I have a 12v winch installed onto a 2 x 2 trailer hitch mount: and I am looking for a 2-way plug to install under my rear bumper. Is there such a thing as a 2-way plug? If so, what is the part #?

asked by: Douglas D

0

Expert Reply:

Sounds like you are looking for standard winch quick connect connectors part # BDW20047 which are what are normally used to make wiring connections to winches.

expert reply by: Jameson C

0

Answer 1

There is only one dust cover offered with the Bulldog Winch Quick-Connect Set for Powersports w/Dust Cover #BDW20047 is because the end where you'd use the included dust cover would also be connected to the battery and if water got in it could…

view full answer...

Answer 2

The Bulldog Winch Quick-Connect Set part #BDW20047 only comes with one cover/plug. The reason for this is because the side attached to the battery would still be live which is the side you would use the plug on as water could get into the connector…

view full answer...

Answer 3

The Bulldog Winch quick connectors #BDW20047 themselves do not have any sort of cover to protect them from the elements. But what you could do is modify mounting box #RP74641 and that will help protect them. There is no one place that you have to…

view full answer...

Answer 4

I did some searching around on the internet and came up with a few interesting tips to prevent rodents from eating vehicle/trailer wiring. Here is what I found: Noise will keep the rodent's away. So a portable radio would work for this. Flashing…

view full answer...

Answer 5

I have a solution for you to maintain your trailer's battery while towing, but we do not offer an aux socket adapter for your battery charger from Schumacher. There is not a great way to charge your trailer's battery while towing, but you can…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement 2-Way Connectors for Winch Connection Made to Wiring

Product Page this Question was Asked From

Continue Researching