Availability of Trailer Hitch for 1996 Ford Taurus With Dual Exhaust
Question:
1996 taurus duel exhaust need trailer hitch
asked by: Keith J
Expert Reply:
According to Curt Manufacturing, their # C12232 Class II hitch fits all models of the 1996 Ford Taurus, including the SHO and wagon. As long as your exhaust system is in the stock position, the hitch will fit great.
If you'll be using the hitch for light duty towing, you'll also need a # C45522 ball mount and a # PC2 hitch pin and for a trailer ball use # A-80 for a 1-7/8 inch or # A-82 for a 2 inch ball. For trailer wiring you will use # C55343 if you have the wagon and # HM40565 if you have the sedan.
The Draw-Tite # 24699 you'd looked at isn't a fit for the SHO, which had a dual exhaust.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Hopkins
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: How Much Does the Curt Trailer Hitch Receiver C12184 Weigh
- Q&A: Recommended Trailer Wire Harness For A 2003 Ford Taurus Sedan
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Q&A: Comparing Curt and Draw Tite Class II Hitch That Fits 2024 Subaru Crosstrek
- Q&A: How to Fight Against Trailer Hitch Rusting
- Q&A: Should Rusted Trailer Hitch Receiver be Replaced
- Q&A: How to Correct Rust on Trailer Hitch
- Q&A: Is the Curt Trailer Hitch Rust Resistant
- Article: Trailer Lighting Requirements
- Article: Trailer Hitch Receiver Sizes