Ball Hole to Pin Hole Distance of Curt Rebellion XD Shock Absorbing Adjustable Ball Mount # C57UR

Question

Question:

What is the distance from the hole in the shank- to the ball hitch on the Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2 and 2-5/16 Balls - 20K ? Concerned about how far the hitch will stick out from the bumper. Thank You

asked by: Brent W

1

Helpful Expert Reply:

The distance from the hitch pin hole to the center of the hitch ball of the Curt Rebellion XD Shock Absorbing Adjustable Ball Mount # C57UR that you referenced is 13-1/4 inches.

expert reply by: Jameson C

1

Ball hole distance
(click to enlarge)

Answer 1

While your Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2-1/2" Hitches - Matte Black #ERT00110 will physically fit the shank of the Shocker Hitch HD Ball Mount #SHK35VR, it will also interfere with the design of the shock absorber. As…

view full answer...

Answer 2

Thanks for the measurements of your coupler and trailer hitch! With that info we know that you need an 8 inch drop to tow your trailer level. The best option for an adjustable ball mount is the Curt Rebellion XD Shock Absorbing Adjustable Ball Mount…

view full answer...

Answer 3

One hundred percent yes, if you are not using weight distribution you can tow your travel trailer using the Rebellion ball mount you asked about: - Curt Rebellion XD Shock Absorbing Adjustable Ball Mount #C57UR The #C57UR will fit your Ram's…

view full answer...

Answer 4

The Curt Rebellion XD like part #C45949-2516 and the Gen-Y Torsion 2-Ball Mount #325-GH-1124 are the two most advanced cushioned ball mounts. As far as cushioning goes the Gen-Y is the winner as it has a design that allows for more cushioning…

view full answer...

Answer 5

Since you have such a light boat trailer I recommend the Curt Rebellion XD #C83WR. This will work better with the lighter amount of tongue weight that you have of 400lbs. The hitch will also be much easier to use for you as it weighs only 43lbs…

view full answer...

Answer 6

I have a solution but I do not have a locking pin that is long enough. Instead the preferred method for locking your coupler to the trailer as well as preventing anyone hooking up to it without permission is the Blaylock EZ Lock Gooseneck Coupler…

view full answer...

Answer 7

The SumoSprings Solo Custom Helper Springs #SSR-127-54 has a maximum capacity of 2,800 pounds as opposed to the SumoSprings Rebel Custom Helper Springs #SSR-129-40-2 maximum capacity of 2,600 pounds. Also, the design is a bit different. Where the…

view full answer...

Answer 8

I have a solution for an adjustable ball mount that is compatible with the GMC MultiPro tailgate, but there is not one that has a specific 5" drop position. It appears you were looking at the B&W Tow & Stow for MultiPro Tailgates…

view full answer...

Answer 9

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Answer 10

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Ball Hole to Pin Hole Distance of Curt Rebellion XD Shock Absorbing Adjustable Ball Mount # C57UR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching