How To Attach 7-way Connector To Draw-Tite Trailer Hitch 75280 On 2006 Honda Ridgeline
Question:
I have a 2006 Honda ridgeline where does the 7 pin plug mount on the 75280 hitch?
asked by: Frank
Expert Reply:
To mount a trailer hitch receiver to the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75280 you were looking at for your 2006 Honda Ridgeline you would need the no drill mounting bracket # 18140 and # 18138 if the 7-way connector you purchase does not include one.
Now to add a 7-way connector to your Ridgeline you will first need to add a 4-way connector using # 118400, and then using the # ETBC7 which will plug into your newly installed 4-way connector and just require a few more connections shown in the included video.
If you are needing a trailer brake controller I recommend taking a look at the Tekonsha Prodigy P3 # 90195 as it is an extremely reliable controller with great features like an easy to read LCD screen and built in diagnostics that are easy to read and understand.
I included videos of the products mentioned for you to take a look at.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How Does Trailer Wiring Secure to Curt Hitch that Fits 2007 Honda Ridgeline
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Differences Between Curt and Draw Tite Hitch for 2008 Honda Ridgeline
- Q&A: Recommended Trailer Wiring Harness for a 2007 Honda Ridgeline
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Replacement for 523185 CR Grease Seal
- Q&A: Troubleshooting Tekonsha Prodigy P2 Brake Controller that Doesnt Recognize Trailer
- Q&A: Meaning of Different Load Range Ratings for Single and Dual Tires on Westlake # LHWL410
- Article: My Trailer Hitch Doesn't Fit
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Rooftop Cargo Carriers
- Article: How to Measure for Trailer Hitch Drop