Most Affordable Trailer Hitch Receiver And Trailer Wiring Kit For 2020 Audi SQ5

Question

Question:

hi do you have a less expensive kit, maybe not so fancy so i can pull a small trailer, thanks

asked by: Mark K

0

Expert Reply:

The most affordable route is to install Trailer Hitch Receiver # e94CR for your hitch receiver then for a trailer wiring kit you can use Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector # C59496.

For a ball mount to slide into the receiver that will allow fitment to your trailer, I recommend looking into Curt Fusion Ball Mount for 2" Hitches 1-7/8" Ball # C45151 if your trailer coupler is 1-7/8" or TowSmart Towing Starter Kit for 2" Hitches - 2" Ball # TS94FR if your trailer coupler is 2".

According to the instructions, the hitch receiver takes about 2 hours to install. While the instructions for the wiring kit do not state how long installation will take, we can estimate that it could take up to 2 hours depending on experience. I attached a couple demonstration videos for you to check out.

expert reply by: Andrew N

0

Answer 1

There is not a hitch that doesn't impact the hand-free sensors. The sensors will still work, you just need to use them more to the side as the hitch will block them directly in the middle. The hitch I recommend for your 2021 Audi Q5 is the…

view full answer...

Answer 2

The etrailer Trailer Hitch Receiver #e94CR isn't going to interfere with the rear traffic sensors on your 2021 Audi Q5. Typically the only issue you would have with a trailer hitch receiver is just with rear liftgate sensors, which is typically…

view full answer...

Answer 3

Let's start real quickly with your question about installation, and no matter which hitch you choose, the install will be the exact same for all trim models of your 2021 Audi Q5. As for the hitches, here are a couple that fit a 2021 Audi Q5: -…

view full answer...

Answer 4

I'd recommend going with the #e94CR Class III hitch for your 2021 Audi Q5. As you can see in the provided photo, the hitch receiver sits pretty tight to the furthest most surface of the back bumper, it doesn't stick out so far that banging…

view full answer...

Answer 5

The Curt 13499 is no longer offered but Curt manufactures all of the etrailer hitches for us so you'd be getting the same thing with the #e94CR, with the only difference being that this hitch comes with a matte black finish. The fitguide can be a…

view full answer...

Answer 6

The difference between the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit - Custom Fit - 2" #391AUDQ518T and the Stealth Hitches Hidden Rack Receiver - Custom Fit - 2" #391AUDQ518 are few. They are the same hitch receiver. One…

view full answer...

Answer 7

Buyers Products #337RT25836B and Curt #C49360 are both 36-inch long 2 x 2-inch receiver tubes with a 5/8-inch hitch pin hole diameter. Both have an outside diameter of 2-1/2-inches. I measured the two items' wall thickness with a digital caliper…

view full answer...

Answer 8

I can't speak to the issue with your OEM ball mount, but for your 2023 Lexus GX 460, any standard ball mount for a 2" receiver will fit the Curt Trailer Hitch Receiver #C13043. It just depends on the rise or drop you need, but two options…

view full answer...

Answer 9

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 10

The hitch tube part #337RT25836B that you referenced has a capacity of 20,000 lbs so if you were to use on your trailer that would weigh around 8,500 lbs you'd have plenty of capacity. Normally this would install on the vehicle side and be used…

view full answer...

Answer 11

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 12

Yes, the Pollak Replacement 7-Pole #PK11893 will fit your wife's 2016 Volkswagen Touareg and here's why... The style of connector this socket is designed to fit is found on nearly all vehicles that have 7-ways. Thankfully all of the…

view full answer...

Most Affordable Trailer Hitch Receiver And Trailer Wiring Kit For 2020 Audi SQ5

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching