TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear

Question

Question:

We recently purchased a fifth wheel camper. I have mobility issues and need steps with a low rise. We have a keystone Avalanche

asked by: Rhonda

0

Expert Reply:

Most RV steps are going to have a drop/rise of about 8". The TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear, # TLA8003, has a drop/rise of 7-1/2" when fully extended. For a four step, # TLA7834. Or a 5 step, # TLA8005. These come in a few different widths as well.

Please see the link attached.

expert reply by: Michael R

0

Answer 1

I wish we had an ideal solution that covered both scenarios, but best option would probably be the steps part #TLA8005 as it's the correct choice for the taller height you'd see. When it's lower the steps would maybe not be as needed.…

view full answer...

Answer 2

The collapsed height of the TorkLift GlowStep Revolution Scissor Steps part #TLA8005 is between 18-1/4 to 19-1/4".

view full answer...

Answer 3

If your TorkLift GlowStep Revolution Scissor Steps have a 27-1/2' wide mounting bracket then the correct Add-A-Step for TorkLift GlowStep Revolution Scissor Steps is part #TLA8001 which is 22" wide. If your TorkLift GlowStep Revolution…

view full answer...

Answer 4

The TorkLift GlowStep Revolution #TLA8003 measures 7-1/2" between steps and yes, they are consistently all the same. The only way they would not be is if you adjusted the landing gear on the bottom, which you can do to ensure they are perfectly…

view full answer...

Answer 5

My TorkLift contact advised that on their GlowStep Revolution Scissor Step #TLA8003 the distance from the top of the frame bracket down to the top step is 7-inches. Unlike most others this step offers some adjustability. If you are at a campsite that…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

Hey Eric, so we have the Torklift Camper tie downs part #TL87DR that fit your 2024 Ford F-250 long bed with a factory hitch. These attach directly to the truck frame so they provide a really great connection point from the truck to the camper.

view full answer...

TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching