Install Instructions Link for Lippert Lift Kit # LC382741

Question

Question:

Can you send me the instructions?

asked by: Andy G

0

Expert Reply:

I attached a link to this page that has the install instructions for the Axle Riser Kit # LC382741 that you referenced.

expert reply by: Jameson C

0

Answer 1

The Pintle Hook #C48215 that you referenced does include mounting hardware to attach to a pintle hook plate like the Super Titan Forged Pintle Hook Plate #RP38186 that you referenced. I also pulled these two parts and was able to determine that they…

view full answer...

Answer 2

The adjustment holes on the Super Titan Forged Pintle Hook Plate part #RP38186 are 17/32" diameter so they will accept and are designed to be used with 1/2" bolts. It should not matter what brand pintle hook is used as the hole size and…

view full answer...

Answer 3

Your Dexter 5,200 lb torsion axles will use the Torflex Lift Kit - Tandem Axle - 2-7/8" Lift #K71-724-02. This is a 2-7/8 inch lift that will work well with your trailer.

view full answer...

Answer 4

Thanks so much for the photos, and based on those, your 2018 Liberty Outdoors Little Guy Max travel trailer has a 3,500 lb Lippert square torsion axle, for which we do have the correct lift kit, which is the following: - Axle Riser Kit - Single…

view full answer...

Answer 5

It sounds like you have a #11 Torflex axle on your tandem axle horse trailer. If that's the case, you can use the Torflex Lift Kit #K71-724-02. This lift kit is designed to be used with #11 tandem Torflex axles that have a 4,100-6,000-lb…

view full answer...

Answer 6

Yes, the Torflex Lift Kit #K71-725-02 is the correct one to use on your 5th wheel trailer with tandem #12 Dexter 7K Torflex axles. This kit will provide an additional 3-1/8 inches of rise and will help level out your trailer so it isn't nose…

view full answer...

Answer 7

Thanks so much for the photo that was super helpful, and what the axle tag shows is that you have a #11 Dexter Torflex axle. We do have the correct lift kit for you, which is the following part: - Torflex Lift Kit - Tandem Axle #K71-724-02 This kit…

view full answer...

Answer 8

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 9

The Axle Riser Kit - Single Square Torsion Axle part #LC382741 will lift both sides of the trailer frame up 3-1/2" to add clearance between the frame and the axle. To install the axle riser kit you want to raise the trailer one side at a time by…

view full answer...

Answer 10

According to Lippert, the mounting nuts should be torqued to 120 ft-lbs for the Axle Riser Kit - Single Square Torsion Axle - 3-1/2" Lift #LC382741.

view full answer...

Answer 11

Your 225/75-15 tires have an overall diameter of 28.4 inches. If you have the vertical and lateral clearance within your wheel wells to move to a 16-inch tire size like 235/85-16, which is 31.6 inches overall diameter and 9.25 inches wide, then this…

view full answer...

Answer 12

In regards to raising a trailer, there will be a few options depending on the type of axle which mind you I cannot look up for any given trailer. If you have a leaf spring axle then you may be able to go with an over/under kit if applicable like part…

view full answer...

Install Instructions Link for Lippert Lift Kit # LC382741

Continue Researching