Can the Race Ramps Trailer Loading Assist Ramps Be Used With Toy Hauler Trailer

Question

Question:

Can these be used to lessen the angle of a toy hauler ramp door when loading a motorcycle?

asked by: Leo S

1

Helpful Expert Reply:

Yes, as you can see in the attached video, the Race Ramps Trailer Loading Assist Ramps part # RR-TR-8 can be used in unison with a trailer ramp door to lessen the approach angle. There is a lip on the end of the ramp that will allow the door to sit flush as well as help keep the ramps in place.

expert reply by: Conner L

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

To test the weight of your ramp door, you will want to get the door all the way down to the ground and then on a scale of some kind (a bathroom scale can be used for this if it's the only thing available). This will be when the door is at its…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 8

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

Yes, the H-Channel for Enclosed Trailer #36281-955 can be used for the side door frame on your enclosed trailer. It is specifically designed for building cabinets and doors on a trailer. There is also the 1/16" Thick Tube Trim for Enclosed…

view full answer...

Can the Race Ramps Trailer Loading Assist Ramps Be Used With Toy Hauler Trailer

Product Page this Question was Asked From

Continue Researching