Replacement Stabilizer Jack for 2021 Jayco Jay Flight SLX 7 174BH

Question

Question:

I broke one of my DOMAR model PJ-01 jacks, and I cant seem to find them anywhere I look. I would like to replace them with something that has a similar bolt pattern at least on the main part. I measured their bracket and hole pattern there is a for a lack of a better work a T with 2 bolt holes the plate is 4 inches with a hole roughly 1/2inch in form each side and on the long axis of the jack a third hole at roughly 17inch I wouldnt mind a sissor type jack if there are any that would work with minimal drilling to work Any advice would be great appreciated, also any advice on put some on the front of our 2021 SLX 7 model 174BH that does not have any fron stands and I have been using stand alone stabilizers Thank you

asked by: David D

0

Expert Reply:

For a replacement jack for your 2021 Jayco Jay Flight SLX 7 174 BH I recommend the Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs # TJ01RT. This jack same mounting hole dimensions as your current jack at 3 inches apart on center. It has a 650 lb capacity per jack and extends up to 18". It is also sold as a set of 2 ,including the handle, which would be the # TJ01RT-HD. These would also be a great addition to the front of your travel trailer.

I have attached a picture showing the dimensions as well as a review and installation video of the jack for your reference.

expert reply by: Robin H

0

Domar Jack Measurements.
(click to enlarge)

Answer 1

Yes, the Replacement Short Arm Assembly for RV Awnings part #LC404523 is correct for a Solera V000436372 Awning.

view full answer...

Answer 2

When you tighten the two nuts on the studs of the Trailer Spare Tire Carrier #DL22128 you were looking at, it will squeeze the tire against the frame which will keep it secure and won't allow it to slide back and forth. I wouldn't…

view full answer...

Answer 3

Yes, I attached a couple pictures of how a U-bolt spare tire carrier like the part #DL22128 would install on an angle iron trailer like yours.

view full answer...

Answer 4

For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part #LC62ED and the correct replacement drive arm (one with the motor) is the part #LC22ED.

view full answer...

Answer 5

While we do not carry a replacement cap which will allow you to convert your hubs from oil bath to grease we do have a hub and all the components you will need to install a new setup which can be filled with grease. You will need one of each per hub.…

view full answer...

Answer 6

There are a few options to help ease your Sidewinder's coupling with your Reese 5th Wheel Trailer Hitch #RP30047: 1. Make sure that your trailer is level. This will ensure that the king pin is going in straight. The jaws of a hitch are usually…

view full answer...

Answer 7

There is a custom wedge for the 68220 Sidewinder for your Reese Elite 5th wheel hitch: - Sidewinder Wedge Kit for 20,000-lb Reese ELITE, M-Series, or ProSeries Fifth Wheel Trailer Hitches #RP44FR

view full answer...

Answer 8

I do have a recommendation for you as we do not carry the PJ-01 stabilizers. Instead you might consider replacing your stabilizers with the much stronger Ark Drop Down Corner RV Stabilizer Jacks #AR34FR. This will include 2 jacks which are much more…

view full answer...

Answer 9

The Malone TopTier Load Bar Kit for Utility Trailers part #MPG493 fits 4' wide and 5' wide trailer decks so it would not be compatible with your 6 foot wide utility trailer. The Malone Crossbar Conversion Kit for Standard Utility Trailer part…

view full answer...

Answer 10

To add an electric trailer jack to your 2006 Jayco Jay Flight 31BHDS I recommend using one of the following depending on if you want to tie the power into your trailer battery bank or not: - Battery Bank #EJ-3520-BBX - 7-Way Power #EJ-3527-BBX Both…

view full answer...

Answer 11

For your trailer the tracks have openings that go front to back. To secure vehicle tires you would need the openings to run left to right like #E19148. Then you could use #77314 which has e-track fittings. But we can make it work by using a couple of…

view full answer...

Answer 12

The bumps around the edge of the Erickson E-Track Tie-Down Anchor #EM37JR are there to add strength to the flange so that it supports weight better.

view full answer...

Replacement Stabilizer Jack for 2021 Jayco Jay Flight SLX 7 174BH

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching