Timbren Axle-Less Suspension Options With 2 Inch Lift Spindle

Question

Question:

i have a pair of these i bought a while ago with 4 in lift - can i buy 2 inch lift spindles? part number please - no brake needed thanks

asked by: Me M

0

Expert Reply:

I checked with the manufacturer, and there isn't an option for a 2 inch lift for the 2,200 lb Timbren systems. The only options that have a 2 inch lift are the 3,500 lb-rated and 5,200 lb-rated Timbren systems, and they each come with a brake flange welded on, though if you don't want to use brakes you don't have to use that flange.

So if you want to go to a higher-rated system with the 2 inch lift you can use either of the following:

- 3,500 lbs: Timbren Axle-Less Trailer Suspension - 2" Lift Spindle # TASR35HDS07

- 5,200 lbs: Timbren Axle-Less Trailer Suspension - 2" Lift Spindle # TASR5200S05

With either of these parts, the correct hub is the Easy Grease Trailer Hub and Drum Assembly # AKHD-655-6-EZ-K.

expert reply by: Kyle S

0

Answer 1

Hey John, To have enough clearance for the trailer with a leaf spring suspension to travel over bumps in the road you want to have at least 3 to 4 inches between the tire tread and the fenders as well as 1 to 2 inches between the side wall and inside…

view full answer...

Answer 2

You can confirm your axle capacity by pulling one of your hubs and looking at the reference numbers on the side of the bearing cages. A 3500 lb axle typically has an L68149 inner/L44649 outer bearing. Torsion axles do indeed wear over time which is…

view full answer...

Answer 3

I'll start off by saying that wheels and tires do not come with hubs, and what hubs you'll be able to use depend on the spindles on the axles, and whether or not you'll want brakes on the trailer or not. If you're going to be using…

view full answer...

Answer 4

The Lock N Roll Articulating Coupler #336TS504 dimensions for the A-frame are 2.19" at the narrowest part and 11.22" at the widest part of the opening. It is 9.68" long from largest opening to narrowest. I have included a picture below…

view full answer...

Answer 5

There are 4 wires coming out of the back of the Draw-Tite Activator IV Brake Controller part 5504. You are correct in that the black wire runs to the positive side of the vehicle battery through a circuit breaker. The white wire runs to the negative…

view full answer...

Answer 6

The 2013 Wrangler Unlimited isn't equipped with a plug-in connector for installing a brake controller, but you can still hardwire the controller. The install isn't terribly difficult, we have some resources to help you though the…

view full answer...

Answer 7

The Timbren suspension system, like #A20RS440, is designed to be toe-in when there is no load on it. So when the load is placed on it it will push the tire out so that it is riding straight on the ground. Provided the trailer is not overloaded and…

view full answer...

Answer 8

Timbren does have spacers, #A25723-90AH00, that you could use. You would need a total of 4 of them since each is 1 inch tall and because you have a 2 inch lift. I have included a couple of video links for you. One is an installation of kit…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

view full answer...

Timbren Axle-Less Suspension Options With 2 Inch Lift Spindle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching