Dimensions for Puck Placement for Install of Reese Elite Rail Kit # RP30126

Question

Question:

My truck has a thick spray in bed liner is there a template to locate where to drill holes

asked by: Stephen M

0

Expert Reply:

I attached a picture that shows where to measure on your truck to determine where the holes for the pucks would be for the # RP30126.

expert reply by: Jameson C

0

Measurements for Locating Puck Holes
(click to enlarge)

Answer 1

When you install a fifth wheel rail kit like the custom kit part #RP50082-58 in the bed of your 2002 Ford Super Duty long bed the king pin center will be approximately 52-5/16 inches from the rear edge of the truck bed. The rear edge of the rear rail…

view full answer...

Answer 2

If I understand correctly you are looking to install the factory pucks in your truck. If that is the case I don't have the drilling measurements for you as we don't carry that kit for your truck. I can tell you the pucks are 30 inches on…

view full answer...

Answer 3

I went out to the warehouse and measured the Reese Universal Mounting Brackets, part #RP58314. The size of the round holes on the brackets is 9/16-inch and is made to accept a 1/2-inch size bolt. The size of the elongated holes on the top of the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Dimensions for Puck Placement for Install of Reese Elite Rail Kit # RP30126

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching