Does Draw Tite Hitch 75703 Fit with Full Sized Spare

Question

Question:

Will 75703 hitch will clear a 245-75R16 spare tire for a 1998 ford club wagon xlt 5.4l?

asked by: Ron

1

Helpful Expert Reply:

Yes the Draw Tite hitch part # 75703 that you referenced will work with a full sized spare.

expert reply by: Jameson C

1

Hitch Installed with Spare
(click to enlarge)

Answer 1

It sounds like you are needing to install a 7-Way connector at the rear of your 2005 Ford E-150. If your Ford Van did not come with the factory tow package (with a 7-way connector), then there will not be a built in socket or harness under the…

view full answer...

Answer 2

First, for a brake controller, in addition to the P3, #90195, you will also need to install a 4-Way wiring harness on the Highlander, #118449. I have included links to the installation instructions for the wiring for you. After you have the 4-Way…

view full answer...

Answer 3

You do not have to have the #ETBC7 to install a brake controller on a 1997 Ford Explorer with a factory 4-Way flat trailer connector. You will at least need #37185. However, the #ETBC7 kit will make installation much easier and will provide all of…

view full answer...

Answer 4

For a 2 inch trailer hitch receiver, you will want a Class III or higher. I have incldued a link to an FAQ article that explains the differences amongst the various hitch classes. For your 2006 Ford E-150 Van, I recommend the Draw-Tite Trailer Hitch,…

view full answer...

Answer 5

Yes, dielectric grease like the Dielectric Grease for Electrical Connectors #11755 can and should absolutely be used on electrical connectors like your 4-pin trailer connector. Dielectric grease does a great job of protecting your equipment from…

view full answer...

Answer 6

The Draw-Tite Max-Frame Trailer Hitch Receiver #75703 is a great fit for your 1983 Ford Van without step bumper. I've attached a photo that shows the fit and no bumper contact. I've also attached a video to further assist. This hitch is a fit…

view full answer...

Answer 7

I reached out to Draw-Tite and they told me the Draw-Tite Max-Frame Trailer Hitch Receiver #75703 was never tested on a 1991 Ford E-150 with the dual fuel tanks. This does not mean it will not fit, it means it has never been tried. I am attaching a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Does Draw Tite Hitch 75703 Fit with Full Sized Spare

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching