Recommended Header Latch Replacement For A TruXedo Lo Pro Tonneau Cover

Question

Question:

I am in need of a replacement part for the rear latch of my tonneau soft roll up cover on my 2016 F150 67inch bed. I have a picture of the broken latch the black plastic portion and then one of the good latch.

asked by: Robert S

0

Expert Reply:

If you have a TruXedo Lo Pro or Edge Tonneau Cover like the one you linked to then you'll just need the Replacement Header Stop # TX1704187.

expert reply by: Kevin C

0

Broken Latch
(click to enlarge)

Tonneau Cover Latch
(click to enlarge)

Answer 1

Recommending replacement components like brake pads and a wheel cylinder for a hydraulic brake assembly without knowing who manufactured it would be very difficult. Are there any part numbers or manufacturer information on them? Without any…

view full answer...

Answer 2

The Extang #EX1032 replacement hinge that you referenced is made for Extang Trifecta and Extang eMAX folding tonneau covers as a hinge replacement. I reached out to my contact at Extang and found out that they also make the Gator covers and that this…

view full answer...

Answer 3

Could you get me pictures of your tonneau cover so that I can identify it possibly? And which exact seals do you need?

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 12

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Recommended Header Latch Replacement For A TruXedo Lo Pro Tonneau Cover

Product Page this Question was Asked From

Continue Researching