Difference Between Valterra Bladex Waste Valves T50 and T50A

Question

Question:

2020 Vanleigh Vilano 370 GB I,m looking to add a waste valve to the end of my dump outlet and would like to know the difference between the Valterra T50 and T50A and which one would I need. Thanks

asked by: Scott

1

Helpful Expert Reply:

So the difference is purely in how the two connect to your sewer pipe, which will also tell you which one you need; one will slide into the pipe (the spigot) while the other will slide onto the pipe (the hub):

- Slide Into Pipe: Valterra Waste Valve for RV Black Water Tank - 3" Spigot to 3" Lug # T50A

- Slide Onto Pipe: Valterra Bladex Waste Valve for RV Black Water Tank - 3" Hub to 3" Lug # T50

To secure the valves to your pipe you would just need the Valterra ABS Solvent Cement # A05-0303.

expert reply by: Kyle S

1

Answer 1

The Valterra Waste Valve for RV Black Water Tank, #T50A has a 3" inner diameter measurement with a 3-1/2" measurement for the outside.

view full answer...

Answer 2

For your Solera Awning, you can use the Replacement Cover for Solera Awnings #LC643923 for the front, and the Replacement Cover for Solera Awning #LC643921 for the back. I have included a couple of videos for you to check out as well.

view full answer...

Answer 3

Since the valves are plastic welded to the sewer pipe you'll have to cut off what you have and install a new one. So you could use the Valterra Waste Valve for RV Black Water Tank - 3" Spigot to 3" Lug #T50A which you'd use the…

view full answer...

Answer 4

The Valterra RV Waste Valve, part #T50A, consists of both the 3-inch valve spigot and the 3-inch bayonet outer cap. You can see this item in the linked review video.

view full answer...

Answer 5

The MaxxFan Dome Roof Vent part #MA00-03812W will work just fine on passenger vehicle with thin metal roof as many others have done so as well. That said, you will need to add some material like plywood between the roof and fan to get the required…

view full answer...

Answer 6

Your thinking is 100% correct here. RV black water drains will be a standard 3" size, which is the internal diameter of the pipes, so the Valterra Waste Valve for RV Black Water Tank - Twist On - 3" Bayonet Hooks to 3" Lug #T58 will…

view full answer...

Answer 7

I looked up the Bristol V33B2R and the correct replacement is the Bristol RV Waste Valve - Sewer Wye - Rotating - 3" and 1.5" Hubs to 3" Lug #34466N3AR which has the hub style fittings for the 3 inch and the 1.5 inch sections which…

view full answer...

Answer 8

That appears to be the Aluminum Eagle wheel from Lionshead. We currently only carry this wheel in an 8 lug 16" x 7". Our most similar wheel in a 15x6 is the Aluminum Liger Trailer Wheel #LH49FR. This is similar in design and color to your…

view full answer...

Answer 9

I went out to the warehouse and measured the dimensions of the Double RV Waste Valves #T84 that you referenced. Width - 4-1/2" Length - 12" Height to Closed Handle - 9-1/4" Height to Open Handle - 12-3/4" I have attached a photo…

view full answer...

Answer 10

The lugs of a sewer pipe fitting can not be fixed so you would have to completely replace the fitting. To do that you'll have to first empty out the tank, which since your lug fitting has broken off will require you to hold the hose in place to…

view full answer...

Answer 11

When gluing together Valterra RV sewer pipes like the #T1028 you'd need to use an ABS solvent cement like the part #A05-0303.

view full answer...

Answer 12

According to my LaSalle/Bristol representative, neither the valve size itself nor the spacing of the holes for the mounting hardware have changed over the years. The mounting holes are 3.73 inches apart center to center, which is right between 2-5/8…

view full answer...

Difference Between Valterra Bladex Waste Valves T50 and T50A

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching