How Much Does the BedSlide 1000 Classic Truck Bed Slide Tray 1,000 Lbs Weigh

Question

Question:

How much does this weigh? Looking to see how much payload I would have after installing this in my truck.

asked by: Dan M

0

Expert Reply:

The BedSlide 1000 Classic Truck Bed Slide Tray - 1,000 Lbs part # BE24ER weighs around 200 lbs.

expert reply by: Conner L

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hello Tom, you are correct. Both the BedSlide #BE48ER and the #BE24ER are a fit for the 2024 GMC Sierra 1500. The only difference is the color of the tracks and the rails. The #BE48ER is all black while the #BE24ER has steel tracks and rails.

view full answer...

Answer 4

Hi Tom; the CargoGlide 1000 Sliding Tray for Trucks #CG1000-9548 weighs 175 lbs. This is confirmed to fit your 2024 GMC Sierra 1500 long bed.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Air bags like the Air Lift LoadLifter 5000 #AL88289 should be filled to a minimum of 5 PSI at all times. Filling them beyond that is done after the truck is loaded. The steps will go as follows: 1. Inflate air bags to at least 5 PSI 2. Load…

view full answer...

Answer 9

Both of the Air Lift Loadlifters, the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle, part #AL57289, and the Air Lift LoadLifter 7500 XL Air Helper Springs - Rear Axle, part #AL57589, will fit your 2022 Ram 2500. One of the differences…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

For your 2019 Ram 2500, I recommend the 5,000 lbs Air Lift LoadLifter Air Helper Springs item #AL57289 over the higher capacity 7,500 lbs item #AL57589. 5,000 lbs capacity is more than enough for your truck. The higher capacity ones would affect the…

view full answer...

Answer 12

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

How Much Does the BedSlide 1000 Classic Truck Bed Slide Tray 1,000 Lbs Weigh

Product Page this Question was Asked From

Continue Researching