Can I Use The Etrailer Drop Leg, Part JF-1005H-Z, With A Round A-Frame Trailer Jack, Part TJA-2001-B

Question

Question:

Is the leg Item # JF-1005H-Z compatible with this jack?

asked by: Paul A

0

Expert Reply:

Yes, the Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter Footplate - Zinc, part # JF-1005H-Z, is compatible with Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs, part # TJA-2001-B.

I have included a product description link and video review links below.

expert reply by: Mark Smith

0

Answer 1

We have a really great trailer jack replacement for what you have with the etrailer Sidewind Jack part #TJA-5000S-B. This is a sidewind jack like what you have but as you can see in the attached install video it can install with the handle on the…

view full answer...

Answer 2

I looked through all of our available manual A-Frame trailer jacks and the option with the shortest retracted bracket height is the etrailer.com A-Frame #TJA-2001-B. The retracted bracket height is right at 5-1/8 inches from the ground and it has a…

view full answer...

Answer 3

I looked through all of our available manual A-Frame trailer jacks and the option with the shortest retracted bracket height is the etrailer.com A-Frame #TJA-2001-B. The retracted bracket height is right at 5-1/8 inches from the bracket and it has a…

view full answer...

Answer 4

The Round A-Frame Trailer Jack #TJA-2001-B has standard mounting hole dimensions which are 3 inches apart center on center. I went to the warehouse to measure and found the same dimensions. I also used a digital caliper to measure the holes…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Can I Use The Etrailer Drop Leg, Part JF-1005H-Z, With A Round A-Frame Trailer Jack, Part TJA-2001-B

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching