Will Replacement Foot Pad for Hydraulic Ground Control Fit with 9 Inch SnapPad

Question

Question:

I need a leveling jack foot and snap pad for a Lippert Leveling system on a 2016 Thor hurricane 35C. I found the 9 inch Foot Pad # LC324269 and the Snap Pad # SP54FR. Are these the correct parts that I need?

asked by: Robert C

0

Expert Reply:

If the Lippert leveling system on your 2016 Thor Hurricane 35C is the hydraulic Ground Control system then yes, the Replacement Foot Pad # LC324269 is what you need and the SnapPad # SP54FR for a 9" round jack foot will fit it.

Attached are some review videos for you to check out.

expert reply by: Jon G

0

Answer 1

The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 #LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube…

view full answer...

Answer 2

I understand your concern. I called Lippert to verify that the 132 Ft-lb of torque and use of Locktite is still valid. They said that was the requirement and there were no alternative instructions. The assumption is that this is the method they used…

view full answer...

Answer 3

The Replacement Foot Pad #LC324269 that you referenced uses (and includes) a threaded 7/16" bolt for mounting. The mounting hole itself is just about 1/2" in diameter.

view full answer...

Answer 4

I suggest using a strap wrench to hold the cylinder side while tightening the installation hardware on the Replacement Foot Pad, #LC324269.

view full answer...

Answer 5

The exact replacement foot plate for the Level Up system you have is not available as a replacement. But you could use #LC314667. The issue is that it uses a smaller bolt than the Level Up foot. So you would have to use a 1/2 inch bolt that will…

view full answer...

Answer 6

The Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269 needs to be torqued to 132 ft-lb. Lippert also recommends using Loctite Threadlocker 262 #LT37420 to prevent the bolt from loosening.

view full answer...

Answer 7

You'll have to hold the leg of your jack still so that you can unscrew the bottom of the foot pad to replace it. If you have a large set of channel locks you could do this pretty easily with them. The trick will be hold it tight enough to keep it…

view full answer...

Answer 8

For your Lippert Level Up Hydraulic Leveling System, you can use the: -Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269. These replacement feet are 9" in diameter, and also includes the o-rings, the bolt, and…

view full answer...

Answer 9

I spoke with my contact at Roadmaster, and it is possible that the Rollaway trailer hitch protector #RM-050 will work with your Valley trailer hitch, but they could not guarantee this. The most important determining factor would be whether the safety…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Will Replacement Foot Pad for Hydraulic Ground Control Fit with 9 Inch SnapPad

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching