Do Chain Hangers Require Trailer Frame Drilling for Curt MV Weight Distribution System
Question:
Curt W/D- The book said nothing about mounting the snap-up hooks to the trailer. Here is my question, Do you have to drill and bolt the snap hooks to the trailer? The only video I found showed the snap hooks not being bolted to the trailer. But mine have bolt holes. Thanks for the information.
asked by: Al T
0
Expert Reply:
The chain lift brackets that come with the Curt MV Weight Distribution System # C17052 have a single 1/2" bolt that is used to secure the bracket to your trailer frame. The instructions call out to turn the bolt until it makes contact with your trailer tongue and then tighten it another 1/4 turn.
The only time you would have to drill into your frame for a kit like this is if you didn't have the room for the standard lift brackets and you needed to install the brackets # C17005.
expert reply by: Jon G
0
Products Referenced in This Question
Chain Hangers for Curt Weight Distribution Systems - Bolt On
- Accessories and Parts
- Weight Distribution Hitch
- Chain Hangers
- CURT
more information >
Product Page this Question was Asked From
Curt MV Weight Distribution System - Round Bar - 10,000 lbs GTW, 1,000 lbs TW
- Weight Distribution Hitch
- WD Only
- Includes Shank
- Electric Brake Compatible
- Surge Brake Compatible
- Fits 2 Inch Hitch
- 900 lbs
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Similar Expert Q&A Pages
- Can 800 lb Spring Bars be Used With 1,000 lb Curt MV Weight Distribution
- Bar Length of Curt MV 10K Weight Distribution System
- Pole Tongue Adapter For Chain Style Hangers Weight Distribution Hitch System
- Curt MV Weight Distribution System for a 5,000 lbs Trailer and a 1999 Dodge Ram 2500
- Weight Distribution Hitch for 400-600 lbs and 800-1000 lbs Tongue Weight
- Weight Distribution Hitch Shank With 6 Drop Recommendation For A 2006 Ram 2500
- Can Curt Weight Distribution System be Used with Curt Friction Sway Control
- Can Trailer be Backed Up With Curt MV Weight Distribution System Installed
- Solutions for Toyota Tundra Rear Sag When Towing with Weight Distribution System
- Recommended Curt MV Weight Distribution System for Trailer with 425 Pound Tongue Weight
- Do Install Instructions Come with the Curt Weight Distribution C17052
- Replacement Spring Bar Retaining Pin and Clips For a Curt Round Bar Weight Distribution Hitch
- Weight Distribution Recommendation for Palomini 180FB
- Solution for Replacement Parts for Discontinued 10,000 Pound Draw-Tite Weight Distribution Hitch
- Weight Distribution System or New Shank with More Drop to Tow Trailer Level
- Do Round or Trunnion Bar Weight Distribution Systems Offer Better Ground Clearance
- Weight Distribution for a 1993 Chevy S-10 Blazer and 3,500 Pound Travel Trailer
- Are There Replacement Spring Bars for the Draw-Tite 3221 Weight Distribution System
- Selecting Weight Distribution/Sway Control Hitch for Travel Trailer with 300-Lbs Tongue Weight
- Shipping Weight of Curt MV Weight Distribution System # C17052
- Recommended Weight Distribution System for 6300lb Trailer w/ 550lb Tongue Weight
- Do Curt C17052 and C17057 Round Bar Weight Distribution Systems Use Same Weight Distribution Head
- Comparing Ground Clearance of Trunnion and Round Bar Weight Distribution Systems
- How Close to Vehicle Tongue Weight Capacity Can You Go
- Recommended Way To Use Weight Distribution On A Trailer That Has A Battery And Propane Tank
- How to Determine Tongue Weight of Trailer for Picking Out Weight Distribution System
- Is Sway Control Needed with Weight Distribution System on Newer Ford Truck
- Weight Distribution Recommendation for Trailers with Gross Weight of 7,000 Pounds
- Will a Curt Weight Distribution System Fit on a Trailer with an I-Beam Frame