Ways to Power an Electric Trailer Jack without a Trailer Battery
Question:
I saw a post on your website that explained how to convert a Bulldog electric jack to using a 7 way connector. Im interested in the Atwood product and wondering if it could be converted similarly to either the 4 flat or 7 way connector. I called Atwood tech support and the lady there said I dont know how you would go about doing that - ask a dealer.
asked by: Wayne
Expert Reply:
Typically we recommend running a powered jack like the Stromberg Carlson Electric Trailer Jack # JET-5000, from a 12 volt battery, but if you wanted to run it to a 7-way you would need to run the power wire to the 12 volt accessory circuit of your 7-way.
There would not be a way to run this product to a 4-way since there isn't a 12 volt power source on 4-ways. If you have a 4-way you would need to convert it to a fully functional 7-way first. For that you would want to use a 4 to 7-way Adapter part # ETBC7. I attached installation instructions for the product for you to check out also.
Products Referenced in This Question
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Leveling Jacks
- Tongue Jack
- Steel
- 4001 - 5000 lbs
- Electric Jack
- 23 Inch Lift
- Bolt-On
- 1 Jack
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Q&A: Using a 30 Amp RV Surge Protector with 50 Amp Service
- Shop: Power Watchdog Surge Protector with Bluetooth - Portable - 30 Amp
- Shop: Mighty Cord RV Power Cord Adapter - 30 Amp Female to 50 Amp Male - 12" Long
- Shop: Trailer Wiring
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Trailer Wiring Diagrams
- Shop: Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
- Article: 5 Things to Know About Weight Distribution Hitches
- Shop: Replacement Tie-Down Ring for Super Track System - Spring-Loaded Mount - 1" - Qty 1
- Shop: B&B RV City Water Inlet - Plastic Check Valve - Recessed Dish Mount - Polar White
- Search Results: water inlet
- Shop: MORryde Locking RV Storage Box - 10" Deep x 25-3/4" Wide x 10" Tall - 1-1/2 cu ft
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Shop: RV Roof Membrane
- Q&A: How to use 12V Power Jack With Trailer That Doesnt Have a Battery
- Search Results: sealant rv roof repair
- Search Results: butt connectors wiring
- Search Results: weight distribution hitch
- Q&A: How to Determine which Dexter Axle is on a Trailer
- Article: 5 Tips to Confidently Choose Your Weight Distribution Hitch
- Search Results: gas struts
- Search Results: hitch
- Search Results: equalizer hitch
- Q&A: Recommended Weight Distribution System for a 10,000 lbs Travel Trailer
- Video: Equal-i-zer Weight Distribution System w/ 4-Point Sway Control Review
- Video: How to Set Up Your Curt Trailer Hitch Receiver on a 2002 Chevrolet Silverado
- Q&A: The RhinoFLEX RV Sewer Hose # CAM39761 Dimension And Compatibility
- Video: Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch Review
- Video: A Closer Look at the Camco RV Fresh Water System Backflow Preventer