Replacement Operator Mechanism For MaxxAir MaxxFan 4401K Roof Vent

Question

Question:

MAXX Fan Smoke 4401K has broken gear that opens cover. Do you sell those parts?

asked by: Lucien C

0

Expert Reply:

The gear that you're talking about on your MaxxFan 4401K is the operator mechanism. For a replacement you need the # MA10-20281K-1AF.

expert reply by: Robin H

0

Answer 1

In the spring mount style of puck light the closest option we have is the part #DG52445VP that you referenced but would require you to slightly open up the holes in your ceiling if what you have is 2-3/4 inches in diameter as this needs a 3 inch…

view full answer...

Answer 2

What you have appears to be a standard puck light which you could use the part #277-000343 as a replacement for if it's 3 inch in diameter like it looks like. We also have 4-1/2 inch size like part #277-000344 but it does look to me like you have…

view full answer...

Answer 3

Since your existing cut out is 3 inches in diameter you can absolutely use the 12V RV LED Puck Light #DG52445VP. While the #DG52445VP has an overall diameter of 3-1/8 inches, the cut out size needed is just 3 inches, as any hole larger than that…

view full answer...

Answer 4

To install a roof vent lid like the Replacement Lid for MaxxAir MaxxFan Deluxe #MA05-30510 for the MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-05301K, isn't considered to be a difficult task at all. The unit does not have to be removed from the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Operator Mechanism For MaxxAir MaxxFan 4401K Roof Vent

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching