Finding a Replacement Spindle For a 2005 Ranger Single Axle Boat Trailer

Question

Question:

please advise what information you would require to recommend a tapered spindal 13/8 by 11/16 bearings for the noted boat.

asked by: Chris B

0

Expert Reply:

It really comes down to the weight capacity for your axle on your 2005 Ranger boat trailer. As we do not carry any spindles which have a 1-3/8" inner bearing and 11/16" outer bearing. Here are the more common size spindles used today on axles.

#42 E-Z Lube Spindle # TRU37FR for 5,200lb -7,000lb axles
#84 E-Z Lube Spindle # TRU74FR for 3,500lb axles
BTR Spindle # TRU94FR for 2,000lb axles

Once you know the correct spindle size to match the weight capacity of your axle we will be able to determine the correct hub and brakes if they are required.

expert reply by: Bud M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

Hello Darren. Thanks for reaching out, I can definitely help with this. To convert your 2024 Brinkley Z2900 5th wheel over to disc brakes, you will need a disc brake kit, a brake line kit, and electric over hydraulic actuator, and a breakaway kit for…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Finding a Replacement Spindle For a 2005 Ranger Single Axle Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching