Replacement 18 Inch Shank For Weight Distribution Hitch

Question

Question:

Hello my shank is 18 inches long and 14 inches from pin hole to bolt hole, I think Reese makes a 3214 that is the same and Curt makes a 17122 that is the same, BUT I am not sure can you tell me if this is true so I can order one.

asked by: DAVE O

0

Expert Reply:

We have the perfect replacement weight distribution shank for you!

The Curt Weight Distribution Shank # C17122 is 18 inches long and from center of pin hole to center of bolt hole is 14 inches. The shank has a weight capacity up to 15,000 pounds and a tongue weight up to 1,500 pounds. The shank has a black powder coated steel that helps resist rust and corrosion.

I attached a review video link below.

expert reply by: Noah E

0

Curt Shank Dimensions
(click to enlarge)

Answer 1

We do still carry the replacement brake pads for the Reese SC as part #58512, however Reese no longer offers the outer link plates or any other replacement parts for the Reese SC system as it was discontinued in 2018. Other than the brake pads, any…

view full answer...

Answer 2

You are not missing anything and you are correct. The Reese Weight Distribution Shank #RP69FR will provide 8.75" of drop. I have included a picture that shows the drop dimensions between each hole.

view full answer...

Answer 3

The Reese Steadi-Flex Weight Distribution System w/ Sway Control #RP66559 will not be effected by the air suspension in your 2013 Ram 1500. That air suspension levels the bed of your truck for more comfortable travel, but the weight distribution and…

view full answer...

Answer 4

The Equal-I-zer, #EQ37100ET, and Reese Strait-Line, #RP66084, weight distribution systems are both top notch systems that will get the job done for you, but I usually tend to lean towards the Equal-I-zer systems for a few reasons. First, Equal-I-zer…

view full answer...

Answer 5

Reese has updated their weight distribution systems a few times over the years. It is odd that the socket size changed but for the Strait Line system part #RP66083 the correct hardware kit you'd need is the #58133.

view full answer...

Answer 6

The Replacement Bolts and Washers for Reese High Performance Trunnion Weight Distribution (WD) Head #58133 that you referenced is compatible with the Head for Reese Weight Distribution System #RP58167 that is used for your discontinued 66152 WD hitch…

view full answer...

Answer 7

The Husky Center Line Weight Distribution with Sway Control 32217 is for 600 lb to 800 lb total tongue weight capacities (the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 8

Based on the numbers you gave, the Reese Strait-Line #RP66084 is likely going to be the right system for you, but you are going to need to make sure by figuring your total tongue weight (TTW), which is the tongue weight of your fully loaded and ready…

view full answer...

Answer 9

Before getting into my answer I first have to ask if you intend to tow with your 2017 Toyota RAV4? If not you can skip to the second paragraph. The reason I ask is because RAV4 will be an issue. The available trailer hitches are not rated high…

view full answer...

Answer 10

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 11

It sounds like what you are saying is that when you upgraded to the bigger 2019 Ram 2500 that your receiver was too high on the taller truck and now when you connect to your 2018 Keystone Cougar Trailer the coupler is too low. It sounds like you need…

view full answer...

Answer 12

Thanks for the picture! That's a large drop you are needing. I recommend the Curt Weight Distribution Shank - 12" Long - 15-3/4" or 16-1/4" Drop - 1,500 lbs TW item #C17125. The Curt shank is compatible with your Reese weight…

view full answer...

Replacement 18 Inch Shank For Weight Distribution Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching