Replacement Anti-Rattle Hitch Bolt For a Thule Range 4 Bike Rack

Question

Question:

Hi, Im looking for a replacement to a missing hitch bolt that will fit a Thule range 4 bike rack. It is the anti rattle style. Thanks!

asked by: David W

0

Expert Reply:

We do have the hitch bolt that you are needing for your Thule Range 4 Bike RV Rack.

If you are just needing the replacement threaded bolt, it is the Replacement Threaded Hitch Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device # TH62RE.

If you are needing to replace the entire hitch lock assembly, it is the Thule Snug Tite Hitch Lock and Anti-Rattle Device # THSTL2.

expert reply by: Scott S

0

Answer 1

The LongHaul part #Y02476 is 42 inches from the top of the shank that slides into the hitch to the top of the rack. If you measure from the ground to the top of your vehicle hitch opening and then add 42 inches you will know how high you would need…

view full answer...

Answer 2

The length of the arms on the Yakima LongHaul 4 Bike Rack #Y02476 are 28 inches measured from the center of the upright mast to the end of the arms.

view full answer...

Answer 3

I went out to the warehouse and measured one of the Yakima LongHauls, part #Y02476, and it uses a 5/8 diameter hitch pin.

view full answer...

Answer 4

From the hitch pin to the mast is approximately 9" on the Yakima LongHaul, #Y02476.

view full answer...

Answer 5

I checked with Yakima and the LongHaul RV Bike Rack part #Y02476 has a distance of 10 inches between the arms and 12-1/2 inches from outside to outside.

view full answer...

Answer 6

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 7

It looks like you have an older Thule T2 Hitch Mount Bike Rack and the correct replacement hitch bolt/pin for this is the Thule Snug Tite Hitch Lock and Anti-Rattle Device part #THSTL2 for locking or Threaded Hitch Pin for Thule part #TH62RE for…

view full answer...

Answer 8

Bike rack manufacturers do have specific threading so there is no type of standard threaded hitch pin that will work. We do have what you need for your Thule T2 Classic Bike Rack #TH9044-TH9046, the Replacement Threaded Pin for Thule Snug Tite Hitch…

view full answer...

Answer 9

I checked with my contact at Thule and verified that the Thule replacement hitch bolt you are looking for is part #908-1240-54. It is a 12 x 40mm hex bolt with a property class of 8.8. It should be installed with M12 washer, #951-1224-54, and M12…

view full answer...

Answer 10

Thanks so much for the photos, they were very helpful, and based on that and the fact you mentioned it was from 2009, I am almost certain that what you have there is the Thule Roadway 914 bike rack. We do in fact have the correct 1-1/4" to…

view full answer...

Answer 11

For a Curt 1-1/4 inch trailer hitch receiver, the Thule T2 has a couple options. You can use the Thule T2 Classic 2 Bike Platform Rack #TH9045 or the Thule T2 Pro #TH23JV. All of these will be compatible with your Curt 1-1/4 inch hitch. With the Curt…

view full answer...

Answer 12

The Thule T2 Classic Bike Rack for 2 Bikes #TH9045 will work great for your application, but you'll need to remove the batteries from your e-bikes. Since this rack has a max weight capacity of 100 lbs and your bikes weigh in at 52 lbs it's…

view full answer...

Replacement Anti-Rattle Hitch Bolt For a Thule Range 4 Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching