What is the Recommended Breakaway Battery Size for a Single Axle Trailer

Question

Question:

I have a single axle trailer max weight 3600 lbs. How big of a battery will I need just for the breakaway switch?

asked by: Tim

1

Helpful Expert Reply:

The standard battery size for a breakaway system is 5 amp hours. I recommend the Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger part # 20400 which is a complete kit that has everything you need. It also have a cool feature where you can simply press a button to see if your battery is charged and ready to go. It comes with the battery, switch, and mounting box.

expert reply by: Conner L

1

Answer 1

The Engager Trailer BreakAway Kit with Charger and Tester part #20099 is weather resistant but not waterproof. Which means that you would not be able to submerge the battery and box in water but it would withstand inclement weather. Ideally your best…

view full answer...

Answer 2

There is two possible causes making the light on your Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire #20099 to stay on even when the trailer is disconnected. The first is if you have the #20099 wired…

view full answer...

Answer 3

If you found a broken solder joint and disconnected wire inside your trailer breakaway battery box like #20099 and you are sure of where the loose wire connects, then yes, you should be fine soldering the wire back into place on the circuit board.…

view full answer...

Answer 4

You need a breakaway battery charger if you want to maintain the battery charge on your breakaway kit using your tow vehicle's 7-way trailer connector. The 12 volt battery on breakaway kits, like all batteries, will self-discharge over time.…

view full answer...

Answer 5

We have numerous battery boxes, see link below, some are smaller than the battery size you have and some are larger. The box you end up with will most likely have at least one physical dimension that is much larger than the same dimension on the…

view full answer...

Answer 6

I spoke with Hopkins about the yellow light on the Hopkins Engager Push-To-Test Trailer Breakaway Kit part #20400 staying on while the trailer is disconnected and they stated this was likely due to an on-board battery on the trailer sending power to…

view full answer...

Answer 7

Can you please provide me with the exact part numbers that your are referring to?

view full answer...

Answer 8

The TAP breakaway system is actually the same as the Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger part #20400. You can use the Replacement Switch for Curt Soft Trac I and II Trailer Breakaway Kits part #C52010 with…

view full answer...

Answer 9

With the battery inside the box for breakaway kit #20099 there is very little space for anything else. I do recommend using a separate junction box such as #38656 which will also make installing wiring and troubleshooting easier since there will be…

view full answer...

Answer 10

Yes, both Hopkins trailer breakaway kits you referenced, parts #20099 and #20400, are complete and equivalent breakaway kits that differ only in the manner that they mount to the trailer. Part #20099 mounts on the side of the trailer frame while part…

view full answer...

Answer 11

If you are using a breakaway kit like the Hopkins Engager Trailer BreakAway Kit #20099 or #20400 that features a sealed battery in an enclosure then you can mount it sideways if that is a better mounting solution on your trailer. We often see…

view full answer...

Answer 12

If you already have a breakaway switch and trying to find its power source, It is possible that someone could have wired the breakaway switch directly to the main battery on the trailer but it does not come like that from the factory. The breakaway…

view full answer...

What is the Recommended Breakaway Battery Size for a Single Axle Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching