Curt Echo Under Dash Wireless Trailer Brake Controller For a 2017 Land Rover Discovery Sport

Question

Question:

I have a 2017 Land Rover Discovery Sport and have installed the factory wiring and fitted a Curt tow hitch. Would this kit have the necessary wiring to connect to the cars loom? The factory wiring is set up with a 7 pin and a 4 pin plug.

asked by: MEL T

0

Expert Reply:

With your 2017 Land Rover Discover Sport having the factory tow package wiring you will be able to connect the Curt Echo Under-Dash Wireless Brake Controller # C27JR using the Pigtail # C51322. The Manual Override Button # C83HR can be added if you do not want to keep your phone on with the app open to manually activate the trailer brakes when needed.

expert reply by: Bud M

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The Curt Echo Under-Dash Trailer Brake Controller part #C27JR as with most any electric trailer brake controller will draw a very small amount of power even when the vehicle is off so it can save all your settings. That said, the power draw is…

view full answer...

Answer 8

For your 2024 Chevy Silverado 1500 I recommend the Redarc Tow Pro Elite #RED63RR. You can use it along with the Plug in Adapter #3064-P for a plug and play install, since you already have the factory tow package. The Redarc controller is going to be…

view full answer...

Answer 9

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 10

See the wiring diagram below from the Curt Echo #C27JR installation manual. The blue wire is the brake output, the black wire is the 12V power, the red wire is the stoplight switch, and the white wire is the ground. Depending on the vehicle there may…

view full answer...

Answer 11

To install your Reese Pod brake controller in your 2018 Ford Explorer will require the install harness part #3035-P which is a confirmed fit. If you check out the 9:55 mark of the install video I attached to this page you'll see where to find the…

view full answer...

Curt Echo Under Dash Wireless Trailer Brake Controller For a 2017 Land Rover Discovery Sport

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching