What is the Inner/Outer Diameter of the Camco Replacement 90-Degree Exhaust Pipe?

Question

Question:

exhaust pipe Cam44812 24 x 6 What is the ID or OD measurement at the 6 end? thank you

asked by: Robert I

0

Expert Reply:

The Replacement 90-Degree Exhaust Pipe for Camco Gen-Turi RV Generator Exhaust System # CAM44812 you mention has an inner diameter of 1.53" and an outer diameter of 1.51".

expert reply by: Bryce D

0

Answer 1

For your generator exhaust, the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 is designed to be used with the Camco Gen-Turi RV Generator Exhaust System #CAM44461. With that being said, we have not tested the #CAM44812…

view full answer...

Answer 2

Yes, the Camco Gen-Turi Replacement 30" EMT Straight Discharge Pipe #CAM44802 is an extension that can connect to your generator exhaust pipe and the Gen-Turi. I've attached a picture below of a neighbor's setup using this pipe. We also…

view full answer...

Answer 3

The inner diameter of the expanded ends of the part #CAM44812 is 1.53 inches and the outer diameter of the non expanded end is 1.51 inches. So basically this setup is designed to either slip into a 1-1/2 inch pipe or slip over a 1-1/2 inch pipe.

view full answer...

Answer 4

The Generac tailpipe 0E0683 that you are looking for has been discontinued, although you may have luck finding an alternative tailpipe with similar specs. It has an inside diameter of 1-1/4" and appears to measure 11-3/4" long according to…

view full answer...

Answer 5

I went out to our warehouse and doublechecked the length myself and found the overall length of the Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe #CAM44812 to be 30" when including the bend. You are correct that the straight…

view full answer...

Answer 6

In order to install the Camco Gen-Turi RV Generator Exhaust System part #CAM44461 on a motorhome where the exhaust pipe is turned down towards the ground you'll need to cut that section of the exhaust pipe off. Once this is done, you can use the…

view full answer...

Answer 7

Here are the inner and outer dimensions for the Camco Gen-Turi items you asked about. Part #CAM44872 – OD is 2.94 inches and ID on the small end is 2.69 inches. Part #CAM44862 – OD is 1.51 inches and ID is 1.25 inches on the flared end. No dimensions…

view full answer...

Answer 8

The Replacement 90-Degree Exhaust Pipe for Camco Gen-Turi RV Generator Exhaust System #CAM44802 you mention has an inner diameter of 1.53" and an outer diameter of 1.51" and while it wasn't designed for use with your Cummins generator…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What is the Inner/Outer Diameter of the Camco Replacement 90-Degree Exhaust Pipe?

Product Page this Question was Asked From

Continue Researching