Is it Possible to Carry a 2 inch Bike Rack on a 1-1/4 inch Hitch
Question:
Can I use a 1-1/4inch to 2inch Hitch Adapter ? My bike rack is 2inch . My rack is about 50lb and lets say my bikes are 25lbs each so as long as I stay under 200 lbs I should be ok? Thanks!
asked by: John R
Expert Reply:
The thing about hitch adapters and hitch extenders is that they reduce the rating of the hitch by 50%. So if you had the Draw-Tite, part # 24787, that has a 200 lb tongue weight capacity you would only have 100 lbs of tongue weight capacity if you were to use an adapter.
Based on the weight of your bikes and rack that would put you dangerously close to the capacity. If you decide to go ahead with this setup I would recommend the use of a stabilizer strap like part # 18050 to help the hitch handle the additional leverage of the hitch adapter. I attached a review video to show you to use the strap.
For an adapter you could use a Hitch Adapter part # HTAD.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver
- Hitch Adapters
- Hitch Expander
- Bike Racks
- Cargo Carriers
- Hitch Mounted Accessories
- 7-1/4 Inch Extension
- Fits 1-1/4 Inch Hitch
- 1-1/4 Inch to 2 Inch
- Brophy
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Video: DIY 2005 Honda Accord Installation for the Draw-Tite Sportframe Trailer Hitch Receiver
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Installation: Curt Trailer Hitch Receiver on a 2004 Honda Accord
- Video: Mount: Draw-Tite Sportframe Trailer Hitch Receiver on a 2006 Honda Accord
- Q&A: Recommended Trailer Hitch and Wiring for 2005 Honda Accord
- Shop: Roof Rack
- Shop: Trailer Wiring
- Shop: Air Filter
- Shop: Floor Mats
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Q&A: Can You Lift A Vehicle Using The Rear Curt Hitch Receiver
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Ultimate Overview of the No-Drill Mount for Electrical Mounting Bracket
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch
- Video: Finding the Right Trailer Wiring Harness
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Search Results: hitch
- Video: Step-By-Step Installation Tutorial for the etrailer Trailer Hitch Receiver on a 2024 Toyota RAV4
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Shop: Brake Controller
- Search Results: trailer brake controller
- Search Results: roof rack
on Trailer Hitch
