Ball Mount Recommendation that is 4 inches Shorter than the Sportframe Ball Mount part # 3594
Question:
Could I get this 3594 ball mount with a shorter shank I am using it on a 2013 Harley Davidson Street Glide and it needs to be 4 inches shorter or do I just have to cut and redrill the pin hole ?
asked by: Chris T
Expert Reply:
I believe the closest thing we have to the Sportframe Drawbar part # 3594 that you referenced that is 4 inches shorter would be the Curt Class I Drawbar # C45027. The length of this ball mount from the center of the hitch pin hole to the ball hole is 6-1/4 inches and it has a rise of 2-5/8 inches.
Basically this ball mount is 4 inches shorter than the ball mount you referenced but its rise is about 1-1/2 inches lower.

Products Referenced in This Question
Curt Class I Drawbar - 2-5/8" Rise, 3-1/4" Drop - 6-1/4" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Similar Expert Q&A Pages
- Which Ball Mount and Hitch Ball Should I use with My Draw-Tite 24797 on my 2009 Kia Rondo
- Recommended Ball Mount for 2010 Ford Fusion Towing Haul Master Trailer
- Ball Mount Recommendation for a 2014 Subaru Forester with a Curt Hitch # C12100
- 7-Way for 2017 Honda CR-V and Ball Mount With 2 Inch Hitch Ball
- How to Pick Out Correct Ball Mount for 2015 Ford F-150
- Pin Hole to Hitch Opening Distance on 2 inch and 1-1/4 inch Hitches
- How To Determine What Size Ball Mount Will Fit On 2006 Chevy HHR
- Towing a Trailer with 2014 Mustang GT vs 1999 Honda Civic Coupe
- Does Suspension Sag Factor When Picking Out Correct Rise/Drop Ball Mount
- Which is Correct Ball Mount for 1997 Chevrolet Lumina w/ Draw-Tite Trailer Hitch # 24628
- How to Determine Where Ball Mount Platform for 3594 Will End Up When Installed on 1998 Buick Regal
- Compatibility of the Sportframe Drawbar and a 2 Inch Trailer Ball With 3/4 inch Shank
- Why do Some Ball Mounts Have a Drop and Rise and Others Only have a Rise
- Dimensions Of Draw-Tite Sportframe Ball Mount # 3594
- How to Measure to Determine How Much Drop Is Needed for a Ball Mount
- Will Sportframe Drawbar # 3594 Fit Kubata RTV Receiver
- How to Measure Ball Mount Rise for Draw-Tite Sportframe Ball Mount # 3594 on a 2002 Buick Regal
- Will the Draw-Tite 3594 Get Me Close to 16 of Rise if My Hitch is 11 1/2 Off the Ground?
- Will Thule EasyFold XT Fit A Class 1 Trailer Hitch with 1-1/4 Distance from Hitch Pin Hole
- What is the Proper Rise/Drop Ball Mount for a 2006 Honda Civic
- Ball Mount For 1-1/4 Inch Hitch On a 2002 VW Beetle with 4 Inch Rise
- Lock Pin Hole Measurement for Class I Hitch
- 1-1/4-Inch Ball Mount with 4-Inches of Drop
- Trailer Hitch and Wiring for a 2016 Subaru Impreza Sedan
- Recommended Ball Mount Draw Bar For 1-1/4 Inch Trailer Hitch Receiver With 4 Inch Rise
- Trailer Hitch Recommendation for a 2012 Mazda 3
- Is Drilling Required to Install a Trailer Hitch on a 2013 Nissan Altima Sedan
- Lowering Exhaust and Using Fishwire to Install a Trailer Hitch on a 2013 Dodge Avenger
- Trailer Hitch and Wiring for a 2008 Nissan Altima Sedan