K08-201-9B Hub And TRU37FR Spindle, What Will Be The Distance From The Brake Flange To The Hub Face

Question

Question:

Can you please tell the distance from the front of the brake flange to the Hub Face using #42 spindle # TRU37FR and the Dexter hub/drum #K08-201-9B and Dexter trailer brakes with parking #23-112-113. I am trying to work out the correct tire offset.

asked by: Jake

0

Expert Reply:

With the hub # K08-201-9B and brakes # 23-112-113 in place on the # TRU37FR spindle, the hub face will be 4-1/4" inches out from the front side of the brake mounting flange.

expert reply by: Jesse M

0

Answer 1

If you are only needing an idler hub we have the DeeMaxx #DE96VR which you will need to combine with the Bearings #25580, #15123, Grease Seal #GS-2125DL and either a standard Grease Cap #F001520 or EZ Lube Cap #DC250L-DCRP. For a hub/drum assembly we…

view full answer...

Answer 2

The Dexter Trailer Hub and Drum Assembly with Parking Brake - 6K Axles - 12" Diameter - 6 on 5-1/2 #K08-201-9B you were looking at actually only works with wheels ranging from 14-1/2" - 16" in diameter. This hub and drum will work with…

view full answer...

Answer 3

The Dexter brake assembly set part #23-112-113 is for a 6k axle so the correct hub drum would be the part #K08-201-9B for a non-pre-greased hub that matches what you need.

view full answer...

Answer 4

I recommend the Electric Trailer Brake Kit #AKEBRK-7-D. The dacromet-coated backing plates are corrosion resistant which is ideal for a boat trailer. Both left and right hand sides are included with the kit. The Trailer Hub and Drum Assembly…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 11

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 12

Since the trailer was off of the ground it would not take much voltage to stop the wheels from spinning so they may be getting power but they may not be getting enough power due to a short or wiring issue. But 9 times out of 10 weak trailer brakes…

view full answer...

K08-201-9B Hub And TRU37FR Spindle, What Will Be The Distance From The Brake Flange To The Hub Face

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching