Recommended RV Storage Cover For A 2019 Forest River Flagstaff E-Pro E19FD

Question

Question:

What are the recommendations for an Flagstaff e-pro 19fd?

asked by: Victor R

0

Expert Reply:

The length I'm seeing for your 2019 Forest River Flagstaff E-Pro E19FD is 20' so you'll likely be around 17' in body length and would need the ADCO # AD37ZR since it fits 15' - 18' lengths. If you measure the body and are at or above 18' then you'll want to size up to the # e84VV, which fits 18' - 20' lengths.

expert reply by: Kevin C

0

Measuring For RV Cover
(click to enlarge)

Answer 1

Yes, unfortunately switching from an Atwood GC6AA-9E Water Heater to a Dometic RV Water Heater part #DMC74FR won't be a direct swap. That said, the wiring won't be too different so you should be able to transfer these over without much issue.…

view full answer...

Answer 2

The length I'm seeing for a 2023 Winnebago Micro Minnie 1720FB is 20'5" so if you subtract 3' for the trailer tongue you'd have 17' of body length. For a 17' length I recommend the Adco Olefin HD RV Cover #AD37ZR. This…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Thomas, the most important factors for picking out a replacement leaf spring for a trailer are matching axle capacity and length. Getting the same amount of leaves in the spring pack is actually not a huge priority so I wouldn't worry too…

view full answer...

Answer 5

The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer frame so the spring is hanging freely and then measure from center-eye to center-eye, then for the equalizer you need to measure…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

Hey Doug, That's a good question because fit is really important so the cover stays snug on your trailer, and there is a specific way to measure for the etrailer covers. It's pretty simple, and what you want to do is measure the body of the…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hi Leo; I would start by checking to see if there are axle tags on the axles. They will probably have the capacity on them or at least a serial number the axle manufacturer could use to identify the axle. If the trailer manufacturer is still in…

view full answer...

Answer 11

Thanks for the pictures! Based on the weight of your 2008 Keystone Cougar 5th Wheel, you will want the item #LG-1 landing gear set. You are going to want to measure to be sure this is the right size for you. The two things you will want to measure…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommended RV Storage Cover For A 2019 Forest River Flagstaff E-Pro E19FD

Products Referenced in This Question

Continue Researching