Can Spindles of Dexter Torflex Axles be Replaced

Question

Question:

Dexter Torflex axle P-15 Model SLR Serial D7013419. Is the spindle replaceable?

asked by: Brian T

0

Expert Reply:

Dexter Torflex axles do have spindles that can be replaced but we would just need to know the capacity of your axles to pick out the correct one. For example if you have a 5.2k to 7k axle you'd want the part # TRU37FR. If you have a different capacity axle check out the link I attached to se all of the options we have.

expert reply by: Jameson C

0

Answer 1

The spindles can be replaced. However, they will need to be welded by a certified welder. They use special jigs so that it is concentric and square on the axle or it can cause problems with uneven tire wear and wheel tracking. I've linked our…

view full answer...

Answer 2

To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…

view full answer...

Answer 3

Trailer spindles are welded directly to the axle so to remove one it just needs to be cut off completely using a torch or saw. Then to replace the spindle such as with the EZ Lube #TRU37FR that you were looking at it's extremely important that it…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Can Spindles of Dexter Torflex Axles be Replaced

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching