Replacement Monitor For Voyager AOM 713 Compatible With 3 Camera Input on 2011 Newmar Baystar

Question

Question:

I have a 2011 Newmar Baystar model 2806 with a 3 camera input Voyager AOM 713 screen. 7 inch color with audio. The monitor went out and I am reading others that say it is not available anymore and suggest other model numbers that are compatible and direct replacement with same hook ups. Could you advise me on that and if you have in stock, can I contact you to purchase? I am more interested in new product with warranty. Thank you.

asked by: Armando M

0

Expert Reply:

You are correct Armando that the Voyager 713 monitor is discontinued by Voyager. We do have their Monitor # VO34FR you found that will plug into place of your current monitor. Do understand this monitor does come with a 1-year warranty so you are not completely at risk of it failing right away and would be the same warranty if you replaced your entire camera system. If you prefer to talk to someone on the phone please feel free to call the number at the top of the page.

expert reply by: Bud M

0

Answer 1

The Voyager RV LCD Observation Monitor part #VO34FR is a direct replacement for the Voyager AOM713 Monitor and it will work with all your existing cameras and cables.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 9

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 10

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 11

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 12

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Replacement Monitor For Voyager AOM 713 Compatible With 3 Camera Input on 2011 Newmar Baystar

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching