Do Access Holes on 2014 Subaru Impreza Hatchback Frame Need to be Enlarged for All Trailer Hitches
Question:
I noticed that, on the 2014 Subaru Impreza 5-door, that many customers had to expand the holes in the subframe to allow for the Curt trailer receiver to be installed. Does this trailer hitch require that as well? If it does require it, do you sell a trailer hitch that does not require altering the subframe?
asked by: Cameron
Expert Reply:
On any of the trailer hitches for the 2014 Subaru Impreza hatchback with single exhaust you may need to enlarge access holes in order to install the hitches. Draw-Tite trailer hitch # DT24959 is the same way. Enlarging an access holes is fairly easy using a file, drill, or rotary tool of some kind. The holes normally do not have to be enlarged very much at all if they even need it.
If you plan on doing some towing then I also recommend ball mount # 3593. It includes a pin and clip. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # 118573 (excluding WRX and WRX STi) or # 119250KIT (WRX and WRX STi). I have linked videos and isntructions for the trailer hitch and wiring for you.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Will EcoHitch Stealth Trailer Hitch Receiver 306-X7261 Fit 2011 Subaru Impreza W/ Single Exhaust?
- Q&A: Is There a 2" Trailer Hitch for a 2010 Subaru WRX
- Q&A: Fit of EcoHitch 306-X7211 On 2013 Subaru Impreza Hatchback
- Q&A: Difference Between Square and Round Tube Trailer Hitches for 2010 Honda CR-V
- Q&A: Comparing Curt and Draw Tite Class II Hitch That Fits 2024 Subaru Crosstrek
- Q&A: Trailer Hitch Options that Fit 2011 Subaru Impreza WRX Hatch with Quad Exhaust
- Q&A: Replacement Keys for a Yakima RocketBox Cargo Box
- Article: Performance Chips and Modules
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: Trailer Hitch Receiver Sizes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Which Hitches are Made in the USA
- Article: How to Choose the Right Trailer Hitch Class