Will The Trailer Valet JXS Drill Powered Jack TV36FR Fit A 6-1/2" Tall 4" Wide Frame?

Question

Question:

Will this trailer jack and mounting hardware fit an I-Beam boat trailer that is 6 1/2inch high x 4inch wide?

asked by: Greg

0

Expert Reply:

Hello Greg, thanks for reaching out. Yes, the Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate # TV36FR will indeed fit a 6-1/2" tall 4" wide I-beam frame. The bracket will fit frames up to 6-1/2" tall and 6" wide so it will undoubtedly work for you.

expert reply by: Jesse M

0

Answer 1

Hey Scott, great to hear from you! The Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate #TV36FR will fit trailer frames up to 6-1/2" tall x 6" wide so it will fit perfectly for your application!

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Hello Greg, thanks for reaching out. Yes, the Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate #TV36FR will indeed fit a 6-1/2" tall 4" wide I-beam frame. The bracket will fit frames up to 6-1/2" tall and 6" wide…

view full answer...

Answer 6

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 7

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 8

Hello Gary. For your 2024 Chevy Silverado 2500 HD with short bed it is recommended to have a sliding hitch to ensure that you can get around those really tight turns without damaging the cab of your truck. For a Curt sliding hitch I would recommend…

view full answer...

Answer 9

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 10

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

Yes, you do. Since your 2024 Chevrolet Silverado 2500 has the shorter 6-3/4' bed you will need to use a sliding 5th wheel hitch to avoid running into your rear bumper or smashing you back window when turning. I recommend the B&W Companion OEM…

view full answer...

Will The Trailer Valet JXS Drill Powered Jack TV36FR Fit A 6-1/2" Tall 4" Wide Frame?

Product Page this Question was Asked From

Continue Researching