How to Figure Out How Low the Curt Hitch part # C15810 Would Sit Below Bumper

Question

Question:

How much below the stock bumper does this hang down? The photos of this installed on the Superduty do not have the bumper installed....... Is the receiver as tight to bumper as possible? I want clearance when I am wheeling and not towing. The side plates of the Reese hang down WAY too far, I can clearly see that from your photos. thank you very much,

asked by: David

0

Expert Reply:

While I don't know exactly how far the Curt Hitch part # C15810 would hang below the bumper of your 2002 Ford Superduty I can tell you how you can figure it out. I went out into our warehouse and measured the distance from the mounting surface of the hitch down to the hitch opening and found that it measures 5-1/2 inches. So basically if you measure 5-1/2 inches down below the rear frame of your truck that is where your hitch opening will be.

expert reply by: Jameson C

0

Answer 1

I checked with Curt and can confirm for you that the Curt Trailer Hitch #C15810 will work with your 2010 Ford F-250 or F-350 Super Duty King Ranch that has a Ranch Hand Bumper. Please note that spare tires larger than 20" will not be able to be…

view full answer...

Answer 2

I reached out to my contact at Curt and was able to get a dimension sheet for the Curt Trailer Hitch Receiver - Class V #C15810 referenced in your question. I have attached an image of it for your review. This trailer hitch is designed to fit select…

view full answer...

Answer 3

Your Curt #C15316 is for the deep drop bumper and has a measurement of just over 9 inches according to my contact at Curt. He said the #C15410 is 5.32 inches from the frame to the top of the crosstube and they don't have anything in between those…

view full answer...

Answer 4

I checked with Curt and they sent me the following dimensions based on your picture for the #C15410. Red line measurement 10.55” Yellow Line measurement 5.32” Green Line measurement is 7.5”

view full answer...

Answer 5

We have exactly what you are looking for! You are correct that the Curt Trailer Hitch Receiver #C15810 you were looking at will not fit your 1999 Ford F-350 with an 8" deep drop bumper. Instead I recommend the Curt #C15316 which measures 9"…

view full answer...

Answer 6

For that length of extension we only have 2-1/2 inch hitch options as they are the only size that's going to have the strength for the stress extensions put on the hitch. You would need to upgrade your hitch to the 2-1/2 inch size with a hitch…

view full answer...

Answer 7

The correct hitch for your 2002 Ford F-350 Super Duty FX4 will depend on the bumper it has. You can use the linked page to see all options; just use the Select Vehicle Style drop-down menu to choose the type of bumper that is on your truck. Once you…

view full answer...

Answer 8

The width of your frame indicates that your 2012 Ford F-450 is most likely a cab and chassis model which has the frame width a few inches than a standard truck bed. But if you can measure the distance between the mounting holes on the frame of your…

view full answer...

Answer 9

The drop of the Curt Class V #C15810, which is the distance from the top of the hitch crossbar to the underside of the vehicle frame where the hitch mounting flanges attach to the vehicle is 5.63 inches. The distance from the face of the receiver to…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

How to Figure Out How Low the Curt Hitch part # C15810 Would Sit Below Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching