Brake Assembly Recommendations for the Trailer Hub and Drum Assembly # 8-201-5UC3-EZ

Question

Question:

I also have trailer with this hub. My question is can I get new backing plates with brake pads or any of the brake parts. 12inch drums 6 lug on 51/2 centre. P.S. I ordered brake controler and cable for yall last Friday, got it on Monday. Great costomer service. Thank you,

asked by: Charlie P

0

Expert Reply:

Yes, we do carry the correct brake assembly to go along with the Trailer Hub and Drum Assembly # 8-201-5UC3-EZ. You would want the 12" Nev-R-Adjust Electric Brake Assembly for 6K Axles # 23-458 for the left hand side and the part # 23-459 for the right hand side.

expert reply by: Jameson C

0

Answer 1

I spoke with someone at Aliner and they said the replacement bearings for the 2013 Aliner Expedition Camper are the same as the 2014 model. You will have to measure the bearings on your wheel. I will include a diagram that explains how to measure the…

view full answer...

Answer 2

It sounds like you are trying to pair the Curt Echo part #C51180 to the Bluetooth on your phone which is why the app is not recognizing it. You want to go into your settings on your phone and make sure you disconnect the Bluetooth from the Curt Echo…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Brake Assembly Recommendations for the Trailer Hub and Drum Assembly # 8-201-5UC3-EZ

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching