What is the Hole Spacing to Mount a Jack to A-Frame Trailer Coupler CA-5335-B

Question

Question:

What is the spacing for the holes to mount the jack?

asked by: Anne

1

Helpful Expert Reply:

A-Frame coupler with jack hole # CA-5335-B has the industry standard mounting pattern which is 3 inches between holes on center for the back 2 holes and 2-7/8 inches apart on center from the front hole to either of the 2 back holes.

expert reply by: Michael H

1

click to enlarge

Answer 1

Thanks for the picture of the a-frame jack mounting bolt hole dimensions you have. Based on that we know you have a standard jack mount on your trailer and the Stromberg Carlson Electric Trailer Jack #JET-5000 you are interested in is a confirmed fit…

view full answer...

Answer 2

The Phoenix Electric Trailer Jack with Remote #UF38-944055 has a multiple mount hole pattern. This pattern allows you to position the jack so the motor faces the front of the A-Frame, or it can be rotated so that the motor faces the drivers side of…

view full answer...

Answer 3

There is not a repair kit for the thumb latch of the A-Frame Trailer Coupler - Underslung - Thumb Latch - Black - 2-5/16" Ball #CA-5335-B. While I wish we had an option for you, if yours has busted you will need to replace the entire coupler.

view full answer...

Answer 4

Well, that is a coupler, though it is in bad shape. It is a bottom mount or underslung coupler like #CA-5335-B. You can check the ball cavity to see if it is in working order but all that corrosion makes me think that using its coupler is not going…

view full answer...

Answer 5

The hardware is pretty much standard for 3" channel coupler mounts like the Trailer Coupler - Adjustable Channel Mount part #CTA-400 so we have plenty of kits with new hardware like the Curt Channel-Mount Coupler Hardware Kit part #C25388.

view full answer...

Answer 6

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 7

I have a solution for you but the Reese Weight Distribution w/out Shank #RP66021 that you referenced won't work well for you due to how tall your frame is. So what you'll need to do is install an under slung coupler on your trailer like the…

view full answer...

Answer 8

When you are using a Weight Distribution (WD) system, like the Equal-i-zer Weight Distribution System #EQ37140ET, you will want to extend the trailer jack on your trailer to lift up some on both the tow vehicle and the trailer. This will relieve the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What is the Hole Spacing to Mount a Jack to A-Frame Trailer Coupler CA-5335-B

Product Page this Question was Asked From

Continue Researching