Pollak 7-Way # PK11893-11932 Wiring Diagram

Question

Question:

I recently purchased this item from you. Watching the videos it mentions a picture on the product detail page showing the pin out for the bare wires. I dont see it on your page. Can you send to me please or link to it on your website? Thanks,

asked by: Rodney L

0

Expert Reply:

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole # PK11893-11932 that you referenced.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End #PK12706 will match the colors and locations of the attached photo. I've also attached a wiring article to assist further if the colors don't match functions correctly…

view full answer...

Answer 2

We only had the black #LH94VR you found before so I went ahead and had it added to our site. The replacement wheel you are looking for is the Aluminum Margay Trailer Wheel - 15" x 5" Rim - 5 on 4-1/2 - Gunmetal Gray #LH69VR.

view full answer...

Answer 3

There is no industry standard wiring code. Pollak uses the following: White - Ground Return Black - Clearance, Side Marker, Identification Yellow - Left Turn and Hazard Signal Red - Stop Lamps and Anti-Lock Devices Green - Right Turn and Hazard…

view full answer...

Answer 4

The black wire of the #PK11893-11932 does carry the 12 volt power circuit. This circuit is a 12 gauge wire. The standard amperage rating for 12 gauge wire is 41 amps typically, but this harness has a 30 amp rating. I attached a diagram that has a…

view full answer...

Answer 5

The 12 volt power wire in the Pollak 5th Wheel / Gooseneck T-Connector #PK11893-11932 is 10 gauge. The ground is 8 gauge. The Brake output wire is 10 gauge. All others are 12 gauge.

view full answer...

Answer 6

I have the perfect option for your 2019 GMC Sierra 2500 that will not require you to use an extension harness in order to connect the lighting on your gooseneck trailer. For this, I recommend the 5th Wheel/Gooseneck 90-Degree Wiring Harness part…

view full answer...

Answer 7

No, they can not! The B&W Universal Base Rails item #BWRVR3200 and any other comparable set of rails will not be compatible with a preinstalled gooseneck hitch. I do have quite a few options to potentially add some 5th wheel rails using an…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

On the back of the Pollak 7-Pole, Round Pin Trailer Wiring Socket - Vehicle End, part #PK11720, it is marked alongside the pin with the color of the wire that connects to that pin location. I am also including a photo that will show a 7-Way round pin…

view full answer...

Answer 10

Yes, the 7-Pin Round connector is wired differently than the 7-Way flat RV connector. I will list the typical heavy duty truck wiring connections inside the plug on the trailer side for you. At the index guide for plugging the trailer end in to the…

view full answer...

Answer 11

Thanks for the pictures! The plate you are needing to get behind is for your gooseneck ball in bed hitch. You will have to remove that to reach the bolt. This will allow you to install the Firestone item #F2703 air bags on your 2012 Ford F-250. I…

view full answer...

Answer 12

Look in the bed of your 2012 Ford F-250. Do you see 4 holes cut in the bed around the center of it? If so then you have the factory rail kit. If not then you do not have it. If you do not have it then you would want the part #BWGNRK1111-5W for the…

view full answer...

Pollak 7-Way # PK11893-11932 Wiring Diagram

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching