Will Curt Drawbar Clear Bumper On 2004 Chrysler Town And Country
Question:
Hi, I have a 2004 Chrysler TandC van with a Curt class 2 hitch I need to get a draw bar, 2inch ball and locking pin, I lined up the trailer height to the van height and it looks like a 5inch Rise draw bar # C45014 will do the job, its an older lower snowmobile trailer. Question is the C45014 at 9 5/8 long ok for a 2004 TandC for the ball connector to clear the bumper? It looks it to me but want to make sure. thanks
asked by: Denny S
Helpful Expert Reply:
There is an easy way to make sure you clear the bumper on your 2004 Chrysler Town and Country. You will need a tape measure and a straight edge like a yardstick or a dowel. Hold the straight edge vertically against the rear bumper, making sure it extends below the hitch opening. Then just measure from the center of the hitch pin hole to the straight edge. This gives you the distance you need to clear the bumper.
The Curt Class Drawbar, part # C45014, measures 9-5/8 inches from the center of the hitch pin hole to the center of the hitch ball hole.
If you find that is not quite long enough, you might want to check out part # C45015. This drawbar measures 11-5/8 inches from center of the hitch pin hole to the hitch ball hole.
The 2 inch hitch ball I recommend is the Curt Hitch Ball, part # C40018. This hitch ball has a 3/4 inch diameter shank that measures 2-1/8 inches and has a capacity of 3,500 lbs.
Products Referenced in This Question
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Continue Researching
- Search Results: trailer jack
- Shop: Brake Controller
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Shop: Bulldog Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Video: Draw-Tite Drawbar for 1-1/4" Hitches Review
- Video: What to Know About the Bulldog Round, A-Frame Jack
- Video: 2" Hitch Ball Spec Review
- Video: Feature Review 2" Hitch Ball
- Video: Let’s Check Out the 2" Hitch Ball
- Video: Feature Breakdown: Curt Class II Drawbar
- Video: Hands-On with the Curt Class II Drawbar
- Q&A: Trailer Hitch Ball Recommendation for Curt Ball Mounts C45015 and C45014
- Q&A: Does The Curt Trailer Hitch Receiver # C98DR for 2023 Hyundai Ioniq 5 Reduce Ground Clearance?
- Q&A: Ground Clearance on a 2020 Hyundai Sonata w/ the Draw-Tite DT74MR Hitch Receiver
- Q&A: Ball Mount For a 2013 Chevy Camaro with 1-1/4 Hitch
- Q&A: Distance From Pin Hole to Ball Mount Platform of Curt Ball Mount C45014
- Q&A: Curt Ball Mount for 1-1/4 inch Hitch with More Rise and Length than C45520
- Q&A: My Draw Bar Will Not Fit All the Way Inside My Draw-Tite Hitch 24812 on my Pontiac Vibe
- Shop: Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
- Shop: Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer brake controller
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: brake controller
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
on Trailer Hitch Ball Mount
