bing tracking image

Review of etrailer Trailer Hubs and Drums - Pre Greased Hub with Integrated Drum - AKHD-555-35-EZ-K

content loading

Customers compare AKHD-555-35-EZ-K to these similar products




Products Featured in this Video



etrailer Trailer Hubs and Drums - Pre Greased Hub with Integrated Drum - AKHD-555-35-EZ-K Review


Jeff: Hello, everybody, this is Jeff at etrailer.com. Today, we're going to take a look at this 10 inch pre greased trailer hub and drum assembly for 3,500 pound easy lube axles. Has a five on five and a half inch bolt pattern. Now this trailer and hub and drum assembly will provide the surface area for your brake shoes or your brake magnet to grip when the brakes are activated. It is compatible with both electric, you can see right here where your magnet would attach to, and hydraulic drum brakes where the shoe would grip to.Now, this is a pre greased hub and drum assembly. It's very easy to install.

There's no need to pack any bearings with grease. It will come already greased with lithium complex multipurpose grease, and it does include everything shown here. It includes the pre grease inner and outer bearings. Now the inner bearing is a part number 68149, outer bearing is part number L44649. Does include also the bearing races that the bearings are installed into.

Does include the installed grease seal in the rear here. The grease seal part number is 58846. Does include the two different grease caps, both a standard cap and the easy lube cap, and then five and a half inch by 20 size lug nuts.Now this hub and drum assembly will fit the easy lube trailer axles and the easy lube axles, the one that has a grease circ fitting on the end of the spindle and allows you to grease the bearings without having to remove the complete hub assembly from the axle. It does include this easy lube compatible grease cap, makes lubricating your bearings very fast and easy. Has the rubber plug in the middle, so when this is installed, just like that, all you have to end up doing is pry open this rubber plug, take it off.

And with it installed on there, you'll gain access to the grease circ fitting, put your grease gun in there, pump the grease full of your grease, and then you have them all set to go. You don't have to worry about having to remove all the bearings and the complete hub assembly from the axle.It is a sturdy iron construction. They do use a zinc enriched paint on the drum to add durability. If you notice the bolts right here are zinc finished bolts to resist corrosion. It is QAI and CSA certified.

Few specs again, this is designed to fit the 3,500 pound easy lube trailer axles with the number 84 spindles. This is compatible with standard axles from most manufacturers, including Dexter, Lippert and Alco. Now the actual drum dimension on the inside. Get our ruler here. The diameter inside to inside is right at 10 inches. The width on where the shoes go is about two and a half inches.It is designed to work with a 10 inch brake assembly. The bolt pattern we mentioned is a five on five and a half inch bolt pattern. The wheel studs are a half inch diameter. Does come with the half inch by 20 size lug nuts to go on there, to hold your wheel to it. And the weight capacity on this is 1,750 pounds. So when it's used with one on the other side of your axle, it'll meet the 3,500 pound axle rating.But that should do it for the review on the 10 inch pre greased trailer hub and drum assembly for 3,500 pound easy lube axles. And this has the five on five and a half inch bolt pattern.


Info for this part was:

Employee Jeff D
Installed by:
Jeff D
Employee Ryan G
Installed by:
Ryan G
Employee Joshua S
Video by:
Joshua S
Employee Jacob T
Video Edited:
Jacob T

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.