Best 2013 Mazda 5 Trailer Wiring Options

content loading

Customers compare 118520 to these similar products




Products Featured in this Video




Best 2013 Mazda 5 Trailer Wiring Options


Today on our 2013 Mazda 5 we'll be looking at our best trailer wiring options. Okay, we have two wiring options today. Off to our right we have the Tekonsha T-1, part number 118520. Off to our left we have the CURT T-Connector, part number 56016. Both of our wiring harnesses here will give us our industry standard four-pole flat connector. These will give use the lighting functions required by law in order for us to safely tow our trailer.

We have both our turn signals, our break lights, and our tail and running lights. Our wiring harnesses are very, very similar. I mean there's really no real difference between them besides two different brands and the sizes of our converter boxes here. Now, the one main difference that they have between them is the power output of them. On our Tekonsha T-1 we have 2.1 amps of power provided for our turn signals and our brake lights on our trailer. As far as our tail lights and running lights are concerned we have 5.6 amps of power.

Now that's plenty of power. It's adequate enough to tow a small trailer, but if you have a trailer with a lot of lights on it, or more running lights than you typically would see on a small trailer you might want to look at the CURT T-Connector, because this one provides you with 3 amps of power for your stop lights and your turn signals, and 6 amps of power for the tail lights and running lights. So if you're running LED lights on your trailer, you could actually add a few more lights with the CURT and not have to worry about it causing a drain on your system. Now both of our wiring harnesses have a powered module. The Tekonsha one is a little bit smaller, so it's a little bit easier to conceal than the CURT one here. But both of these will isolate the vehicle's lighting system from the trailer. These will also help prevent any damage from occurring to our vehicle lighting circuitry by being isolated, so if there's a short in our trailer we don't have to worry about that causing any problems with our lighting circuitry on our car.

Now both of our wiring harnesses attach in exactly the same way. Take a look at our Tekonsha here first. As you see we have these two connectors here, they'll go in-line of our vehicle wiring harness here, and then our tail light connector here on both sides. This will provide our connections for our turn signals, our tail lights, and our brake lights. We have the same thing on the CURT here. Same type of plugs, just match up the factory.

There's no cutting, no splicing, or any modification of vehicle required at all. Now our Tekonsha wiring harness has a built-in dust cover to it right here to help protect from the elements and to keep dirt and debris out of it when it's not in use. Our CURT has a one that's separate. Just snaps on over here, and then you can attach it to it like that. Just slightly different. Both of them have all the necessary hardware you need to install. Several zip ties, some double sided tape to mount our box to the vehicle, our fuse, and all the terminals and connectors we need to make our wiring connections. Now both of these wiring harnesses are designed to be kept inside the vehicle, so when it's not in use your four-pole flat will reside inside the vehicle. Where it's designed to be stored is inside your jack storage compartment off here on the driver's side of the vehicle. Just pull that out and grab your wiring. Set it to the side of your trunk latch, and you can close your hatch down on over it. They both have adequate length so they can hook up to your trailer electrical connection very easily. When you're not using it you can just put the dust cover back on, open your hatch back up, store it back inside your jack storage compartment, reinstall your cover. In conclusion, either one of these will work just fine for you, but if you are needing to have more power output to run more lights you might want to look at the CURT just because it has the higher power output. If you're only going to be towing a trailer occasionally, or if you are looking for something that's quick and easy to install you might want to look at the Tekonsha just because it has the smaller box, it's easier to conceal, and I like the fact that it's got the built in dust cover. That completes our look at the best trailer wiring options for the Mazda 5.


Questions and Comments about this Video

Info for these parts were:

Test Fit:
Joe V
Test Fit:
Shane H
Test Fit:
Robert C
Video by:
Andrew K
Video by:
Jonathan Y
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Kathleen M
Video Edited:
Chris R

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.