Trailer Hitch Installation - 2014 Chrysler Town and Country - Curt

content loading

Customers compare 13364 to these similar products




Products Featured in this Video



How to Install a Trailer Hitch on a 2014 Chrysler Town and Country


Kurt: Today in this 2014 Chrysler Town and Country, we're going to install part number 13364 from Curt. All right this is what the hitch looks like when installed on the van. Next I'll give you some measurements to help you out selecting some accessories, such as a ball mount, a bicycle rack, or a cargo carrier. From topper receiver opening down to the ground will be about 13 1/2 inches. From the center of a hitch pin hole, the edge of the bumper will be about 4 1/2 inches. Now Ill go ahead and show you how the hitch is installed. To start off our install we're going to need some room to install our hitch.

First we're going to go ahead and lower the exhaust. So the exhaust hanger right behind the muffler . now if you need more room theres one farther up that we can go ahead and loosen up to give us the most room. With the exhaust out of the way, we can go ahead and show you where our hitch mounts up. Look here at the driver's side, there are three bolts on a frame rail.

We'll have to remove all three of these bolts. This is where our hitch will mount up. On the passenger's side there will be only two bolts, the one closest to the bumper and then one behind that. This is where our hitch will attach.So we'll go ahead and remove these bolts and we'll have to save them, because we'll reuse these to attach the hitch. Okay, once our bolts are removed, we can go ahead and put our hitch up in position.

Its definitely a good idea to get an extra set of hands to help hold it up there. we'll go ahead and do the bolts that are closest to the bumper first. We're grinding a few threads just to hold the hitch up on both sides. Then we'll go ahead and install the rest of our hardware. When you take out the hardware on the passengers side, the bracket on the inside will actually shift to one side or the other. We're going to use a lineman tool to help bring it back into position.

This also could be a large diameter screw driver as well.Just be gentle on the threads and move it until you can get the bolt inside. we've got one install, and that will hold the bracket in place so we can install the second bolt. With all our bolts loosened and installed, we can go ahead and tighten down the bolts. Then after that, we can go ahead and torque the bolts down as specified in the instructions. Okay with everything torqued down we can reinstall the exhaust. With those few steps, our hitch is already installed. Now I'll finish it for part number 13364 from Curt, on our 2014 Chrysler Town and Country. .


Questions and Comments about this Video

Info for this part was:

Employee Joe V
Test Fit:
Joe V
Employee Nicholas E
Test Fit:
Nicholas E
Employee Shane T
Test Fit:
Shane T
Employee Randy B
Test Fit:
Randy B
Employee Jared G
Test Fit:
Jared G
Employee Brent H
Test Fit:
Brent H
Employee Shane H
Test Fit:
Shane H
Employee Robert C
Test Fit:
Robert C
Employee Zack K
Video Edited:
Zack K
Employee Andrew K
Video Edited:
Andrew K
Employee Joshua S
Video Edited:
Joshua S
Employee Jacob T
Video Edited:
Jacob T
Employee Andrew L
Video Edited:
Andrew L
Employee Kathleen M
Video Edited:
Kathleen M
Employee Chris R
Video Edited:
Chris R
Employee Alan C
Video by:
Alan C
Employee Zach D
Video by:
Zach D
Employee Jonathan Y
Video by:
Jonathan Y

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.