bing tracking image

Trailer Hitch Installation - 2016 Volkswagen Golf - Curt

content loading

Customers compare C11412 to these similar products

Products Featured in this Video

How to Install a Trailer Hitch on a 2016 Volkswagen Golf

Today on our 2016 VW Golf GTI, we're going to be taking a look at installing the Curt Trailer Hitch Receiver Class 1. Part number C11412. This is what it's going to look like once it's installed. You can see it's got a nice high gloss black powder coat finish. It's going to be an inch and a quarter by an inch and a quarter square tube with a half inch hitch pin hole. This is a class one hitch.

It's going to allow for two hundred pounds of tongue weight, which is our downward force, and two thousand pounds of towing weight. Now you want to make sure your vehicle is actually ready to haul that much weight by checking with you owner's manual or your manufacturer. It's got a large flat safety chain loop, both sides. It's going to be a simple bolt on design by dropping your exhaust. You're going to use existing holes with some carriage bolts and plates on the inside of the frame. The hitch does come with a hitch pin and clip, but your draw bars are going to be sold separately. One note on a current hitch, if you're going to be carrying a non-wheeled load such as a cargo carrier or a bike rack, you want to make sure you use stabilization straps.

You can see it's going to tuck up very nice along the bottom side of our fascia on the back of our vehicle giving it that sleek and stylish look. Now our first step for our installation is we're going to have to lower our exhaust system down. We're going to put a safety strap underneath to help support our exhaust as we remove the brackets in the back. We're going to have one bolt on each side that's going to hold up our exhaust system. Take a thirteen millimeter socket and lower those down. Then we can slowly lower down our exhaust.

Now we're going to have two locations where we're going to have our bolts come through on either side to hold our hitch. We're going to have a half inch carriage bolt and a block that's going to fit up inside the frame. Now before we can put our bolt through, you want to check and make sure there's not a bunch of undercoat stuck in position there where the bolt's going to come through. You just take a scraper or a file and just clean out the inside of the hole so it'll slip through a little easier. We can take our fish wire and we're going to push it through the hole, and we'll pull it down out of there, we'll place on our black and thread it on our carriage bolt. We'll press our block up into place followed by our carriage bolt.

We'll use our fish wire attached. Our next one's going to be reverse fish wire, so we're going to slide our block on. We'll thread on our carriage bolt, then we're going to insert the bolt in first followed by the block and pull it right back through the same hole. Slip it inside and just push it back, slide up our block and we'll repeat this process for the other side. Now we'll get somebody to help us, second set of hands. We're going to push our fish wires through the bolt holes and feed our hitch up through. Take our flange nut, start it onto our bolt, do the same thing to the next bolt. You want to keep pressure on this just so it doesn't slip back up inside the hole. Just round them up finger tight for now and then take a look, make sure you got your hitch all centered up. Now to tighten up our bolts, we're going to use a nineteen millimeter socket. We'll repeat that for both sides. Now we can torque down our bolts to the specifications listed in our instructions, and we'll repeat that for the other side. Our last step is going to be tighten up our safety strap, put our exhaust back up into place, and we can reinstall our bolts. We can go ahead and re-secure our exhaust hangers and remove our safety strap. That's going to complete our installation. That's going to do it for our look at and install of the Curt Trailer Hitch Receiver Class 1, part number C11412 on our 2016 VW Golf GTI.

Questions and Comments about this Video

Info for this part was:

Employee Joshua S
Video Edited:
Joshua S
Employee Jacob T
Video Edited:
Jacob T
Employee Chris R
Video Edited:
Chris R
Employee Andrew S
Test Fit:
Andrew S

At we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.