bing tracking image

BAKFlip MX4 Hard Tonneau Cover Review

content loading

Customers compare BAK48121 to these similar products




Products Featured in this Video



Review of the BAKFlip MX4 Hard Tonneau Cover


Today we'll be taking a look at the BAKFlip MX4 Hard Tonneau Cover, part number BAK48121. Add some style to the back of your truck while keeping your equipment dry with the BAKFlip MX4 Hard Tonneau Cover. This tonneau cover features a quad fold design which allows you partial bed access and full bed access. Panels offer automatic latches which allow for a secure fit. The safety straps allow you to travel with the tonneau cover folded, and the prop rods keep it secured while folded up against your cab. With our cover folded up, you can see that our rails simply clamp into place. There's no drilling required, and our rails sit inside our truck bed only about an inch and a half.

This tonneau cover has a low profile design that still gives you access to your stake pockets. It's made out of an aircraft aluminum to resist rust and corrosion, and the cover is rated to hold up to 400 pounds if the weight is evenly distributed. Rubber seals ensure that it's watertight. When used in conjunction with a locking tailgate, you can see it keeps your stuff secure inside your bed. Now that we've gone over some features, we're going to go ahead and show you how to install it. Now we're going to install our weather strip.

You want to make sure you have a clean surface to work with. You're going to take the white side, peel off the paper, and stick it to the bulkhead of your bed. If you have some extra on the end, no problem, just go ahead and trim that off. Now we're going to install our side rails. Very simple. This end right here goes up toward the cab.

We're going to take it. We're going to set it in place. When doing this, you want to make sure that your tailgate is closed. Now we're going to take our side rail, and we're going to attach it with the provided clamps to the bed. You want to make sure that your rail's pushed all the way forward.

You're going to take the teeth side of the clamps with the nut facing out, one on the rail, one on your bed. Push it all the way forward as far as you can get it. Hand tighten it down. One thing I do want to mention, you want to make sure your groove is lined up. Now we'll take our 9/16ths inch wrench and tighten it down. Before tightening down all the way, you want to put some pressure on this top ridge here to make sure it sits flush. We'll repeat the same process with the second one, and you want to get as close to the center as possible. Put some pressure on the top rail. 9/16ths wrench to tighten it down. Tighten it in place. For our final clamp, we're going to install as close to the tailgate as possible. Again place it on your rail, slide it back as far as it'll go towards the tailgate, hand tighten it down, making sure your grooves are lined up in your clamp. Take your 9/16 inch wrench, pressure on the top rail, and tighten in place. And now we'll just repeat the same process son the driver's side. Now we're going to install our prop rod. You're going to take the socket end, snap it right on that ball, and then repeat the process on the other side. Now we're going to set our tonneau cover in place. Be a good idea to grab a second set of hands. What you want to make sure is the smaller panel faces forward towards the cab. Now that we have our cover sitting on top here, you want to make sure this front side of this small panel is on the inside of this weather strip. Now we're going to install our buckle. We're going to do, we're going to lift up the flap, you're going to take your provided hole sleeves, slide it into place. Take your buckle, what you want to make sure is that the open end of the buckle is facing toward the bed. Route your screws in place here. Take a Philips screwdriver. One thing I do want to mention is make sure when you tighten these, you don't tighten them down too much, because these are plastic and they can crack. You notice there's a rubber gasket right underneath. Just put enough pressure on it to where it's starting to come out just a little bit. Then we'll repeat the other side. So now we're going to install the cab bumpers. I suggest take your tonneau cover, pushing it up against your cab here, to make sure you put your cab bumpers in the right places so it actually keeps the tonneau cover from touching the vehicle. We're pretty much flat here, so what we're going to do, we're going to start with the center one. you're going to peel off the red strip, and we're just going to stick it down on the cover, and you're going to repeat the process on your other two. At this point, we're going to install our hardware on our cover. If you notice, there's two rubber washers. You're going to install one on the top of the bed cover, the other one on the bottom. So you're going to take the flat part goes through the top and through the plate on the bottom of the bed rail. You may want to grab an extra set of hands just to put a little bit of pressure down on the top of the bolt. You're going to take your three washers, rubber washer facing up. What you want to make sure you do is just loosely put it on, not tighten it down at this point, and then repeat for the other side. Now that our cover is loosely installed, we'll go ahead and fold it out. Before you fold over your last panel, you want to make sure that your tailgate is up, and it should fit just against your tailgate. Now that we have our top in place, we'll go ahead and fold it back up. We'll go ahead and tighten it down. Again I did want to mention, you want to make sure you don't tighten these down too much, just enough where the lock washer is flattened out. The last step is to install our drain hoses. Now go ahead and lay our tonneau cover down, and that'll do it for part number BAK48121 on the BAKFlip MX4 Hard Tonneau Cover.


Info for this part was:

Employee Dustin K
Video by:
Dustin K
Employee Shane H
Video by:
Shane H
Employee Jonathan Y
Video by:
Jonathan Y
Employee Chris R
Video Edited:
Chris R
Employee Zach D
Video Edited:
Zach D
Employee Hayden R
Test Fit:
Hayden R
Employee Jacob H
Test Fit:
Jacob H

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.