bing tracking image

etrailer Trailer Hub And Drum Assembly Reivew

content loading

Customers compare AKHD-655-6-G-EZ-K to these similar products

Products Featured in this Video

Review of the etrailer Trailer Hub And Drum Assembly

Today we're going to be taking a look at the etrailer trailer hub and drum assembly for 6,000 pound E-Z Lube axles. This is going to be for 12-inch brake assemblies, and it's going to have a 6 1/2-inch bolt pattern. So here's what our hub and drum assembly looks like once we have it installed. Now the drum is going to give us area for our brakes to contact so they can make that friction and slow our trailer down. Our drum assembly is going to have a galvanized finish to it, so it's going to be really nice for those marine applications or wherever your trailer may be close to a lot of water.Our hub and drum assembly is going to be a 12-inch diameter, and the bolt pattern is going to be 6 on 5 1/2. It's going to work with 6,000-pound axles, and it is made for the E-Z Lube axles.

You'll notice that in the end of the cap here we'll have a rubber plug. If we pull that plug out, it's going to make servicing the grease fitting right there really easy. We're not going to have to worry about taking the whole cap off. Just pull the plug out and grease up our axle.On our trailer we have electric brakes, but our hub and drum assembly is going to work whether the brakes are electric or hydraulic. As long as you have a 12-inch brake assembly, these will work.

The drum itself is going to be made out of iron, and the actual dimensions of our drum assembly is going to be 12 15/16-inch diameter, and it's going to be 2 3/8 inches deep. Our hub and drum assembly is going to come with everything we need to get it in place. The cap on the end, the seals, the bearings, and even the races, and they're even going to include new lug nuts.Now just keep in mind we are going to have to pack the bearings and put the seal in place, but the races are already going to be installed for us. Our hub and drum assembly does come in a quantity of one. So if you're replacing the entire axle, make sure to pick up another one.

But now that we've gone over the features and seen what it looks like, let's show you how to get everything set up.To begin our installation, you're going to want to lift your trailer up, using jack stands to support it so we can remove the tire. Once we have the tire removed, we're going to need to remove the grease cap on the end of the hub here. Now typically, we'll take a hammer, and we can just kind of tap it. We can take that cap off, but we don't want to damage it. So I'm going to take a flat blade screwdriver and try and get that edge to come up a little bit.

Then just work our screwdriver and pop the cap off.Behind the cap we'll have our castle nut, and we should have some kind of keeper, maybe a cap like this, or you may have a cotter pin. Either way we're going to need to remove that keeper and move it out of the way of our castle nut so we can loosen it up. Now once that tab is out of the way of the castle nut, then we can loosen it up and go ahead and remove the castle nut. Just pull the nut off, and we can start pulling either the ring or cotter pin or whatever is holding it in place. We'll pull that off. If you want, you can actually grab the whole hub and drum assembly and very carefully slide it out, and that'll bring all the bearings and washers and everything else out, and we can grab them before they hit the ground. The bearing may not come out that easily.Then we can pull the entire hub assembly off. So we can grab our hub and drum assembly now. We'll grab the bearings. We're going to have one large one and one small one. We're going to start out with the larger one. Since this is the inside of the hub and drum, we'll take the large bearing, and you'll notice it's tapered. You want the small section to go down, and it's going to fit right inside our hub just like that. But before we fully put it in there, we need to make sure that the bearing's packed with grease.So you want to make sure you have some quality grease, and if you have a bearing packer, it will make it easier. But if you don't, a trick is we can take our bearing. We can open up the can, and we're just going to kind of scoop it almost like you're grabbing some dip for some chips. It's always a good idea to wear gloves because we don't want to get it all over our hands. But we'll grab a bit of the grease, and we just want to push it into the side of the bearing and make sure it fills in that area. We'll just work the grease around, again pushing it in like this until we make sure we have all the cavities filled up.A lot of people have a tendency just to wipe the grease on the outside. It's not about getting the grease on the outside. It's about getting it in between the rollers here, so that's why it's better to start at the core and kind of just push it in there like that. Let's work our way around until we feel comfortable that there's enough grease in there. We'll take our bearing, and we'll drop it in. So it's going to sit nice and flat inside the hub.We can grab our seal. Now the seal is going to be closed on one end and open on the other side. You want to make sure that the open side is facing towards the bearing and that the a flat side is facing towards us. So we're just going to loosely place it inside of our drum here. Now if you have a seal driver, that's going to be an ideal tool to use. But a lot of us aren't going to have a seal driver that's this size, so a trick that you can do is you can take a block of wood. We're going to go right over the center of our seal, and we'll grab a hammer, and we're going to hit the wood until our seal is nice and flat sitting.If it does start to get on an angle like this, you just need to pay attention on where you're hitting the seal and how hard you're driving it in. We're going to go around, and we're going to feel the edge of the seal and make sure it's nice and flush. We can grab our smaller bearing, and we're going to go ahead and grease this up and make sure we have plenty of grease in there. But you want to grab a towel and go ahead and rest it on there when you're done because we're not going to be putting this in just yet.Now we can come back to our trailer. We want to make sure that our spindle is nice and clean before we put our hub and drum on. So let's wipe everything down. Make sure everything's nice and clean. We don't want to have any kind of debris stuck on there. But once that's nice and clean and we have everything wiped down, we'll grab our hub and drum. We'll slide it into place.Now once you initially get it on there, you are going to feel a little bit of tension. We want to make sure that it's fully seated on there and pushed all the way on. Now we can grab the smaller bearing and slide it into place. Slide our bearing in. It kind of helps if you lift it up a little bit. Make sure that bearing goes in there all the way.If it gets off angle, just grab your hub and drum, pull it out, and it'll help recenter that. Take our washer that came off earlier. Put that over the top and grab our keeper ring. Put that in place. Finally, we'll put our castle nut on. I like to tighten these up where they're nice and snug. Then I'll spin my drum a couple times. Back it off just a little bit until we can get that tab on our keeper to line up with the castle nut. I'm just taking a flat blade screwdriver. We're going to bend that tab up, and that'll prevent that castle nut from turning on there.You want to go back and make sure that the hub is full of grease. We'll know it's full because we'll see it start to seep out around that washer. This will also help out. If you didn't pack the bearing as full as you should, this'll make sure the grease gets in there. So depending on how full you packed it, it may be pretty quick that it fills up, but if you didn't, it may take a little bit of time.You can see the grease squirting out of the bearing right behind that washer. That way we know it's full. We'll grab our cap so we can put that in place. Now if we have any more that we're replacing, we'll go ahead and do that. Otherwise, we can put our wheel and tire assembly back on.That'll finish up your look at the etrailer trailer hub and drum assembly for 6,000-pound E-Z Lube axles.

Info for this part was:

Employee Jeff D
Installed by:
Jeff D
Employee Robert C
Installed by:
Robert C
Employee Chris R
Video Edited:
Chris R
Employee Jonathan Y
Video by:
Jonathan Y

At we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.