Pontiac Custom Fit Vehicle Wiring Installation And Review Videos

  

Best 2010 Pontiac Vibe Trailer Wiring Options- Video

Best 2010 Pontiac Vibe Trailer Wiring Options

Speaker 1: Today on our 2010 Pontiac Vibe, we're going to be taking a look at the best custom fit vehicle wiring. Here we have the two best wiring options for your Vibe. Here on this side we're going to have the Curt, part number C56035, and over here we're going to have the Tekonsha, part number 118460.With the Curt, you're going to have 3 amps per circuit for your stop and turn and 6 amps for your taillight, whereas your Tekonsha, you're only going to have 2.1 amps per circuit for your stop and turn and 4.2 amps for your taillights. Because you have to run your power wire through a grommet in the back, your Curt kit is going to come with some black silicone, whereas your Tekonsha is not going to have that.Now your Tereshkova modular box is going to built a little bit better. It has a potting in here that's going to hold your wires in place, and that potting is completely filling the inside of this box. What that does, is if this box was ever to come loose inside the vehicle, the potting that's inside is going to help protect the wires and keep them from disconnecting.Both wiring harnesses are going to install exactly the same. more


Watch Video

8/24/2017 1:47:29 PM



Best 2009 Pontiac Vibe Trailer Wiring Options- Video

Best 2009 Pontiac Vibe Trailer Wiring Options

Speaker 1: Today on our 2009 Pontiac Vibe we're going to be taking a look at the the best custom fit vehicle wiring. Here we have the two best wiring options for your Vibe. Here on this side we're going to have the CURT, part number C56035. Over here we're going to have to Tekonsha, part number 118460.With your CURT you're going to have three amps per circuit for your stop and turn and six amps for your taillight, whereas your Tekonsha you're only going to have 2.1 amps per circuit for your stop and turn and 4.2 amps for your taillights. Because you have to run your power through a grommet in the back, your CURT kit is going to come with some black silicone, whereas your Tekonsha is not going to have that.Now your Tekonsha modular box, it's going to be built a little bit better. It has a potting in here that's going to hold your wires in place. more


Watch Video

8/23/2017 11:27:21 AM



Trailer Wiring Harness Installation - 2010 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2010 Pontiac Vibe

Speaker 1: Today on our 2010 Pontiac Vibe GT we're going to be taking a look at and showing you how to install the Curt T connector vehicle wiring harness with four pole flat trailer connector. Part number C56035. Now this is what our wiring harness looks like when it's installed. As you can see, it's going to lay inside of the vehicle. When you're ready to use it, you just string it out the back of the vehicle. Now you want to make sure you're going over top of this rubber seal here and you're staying away from any connection points that your hatch is going to make. more


Watch Video

8/20/2017 9:58:46 AM



Trailer Wiring Harness Installation - 2009 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2009 Pontiac Vibe

Today on our 2009 Pontiac Vibe, we will be taking a look at and installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C56035. Unlock and pull up the rear spare tire area. Pull our wire out, close down the top . you can lock and secure everything if you want at this point . and this weather seal is going to be strong enough and thick enough that your wire won't get split when it comes down over the top. Now we'll go ahead and hook up our tester and test out our lights. All right, first thing we'll do is pull the cover off and then we'll hook up our ground to the ground side. Then we're going to test out that brown wire, which will be our running lights. We'll have that constant signal turn off. Now we'll test out the left-side turn signal, which will be the yellow and the passenger-side which will be the green wire. Now, we'll go ahead and check our brake lights which will be both the green and the yellow constant. Our wiring looks good, so we'll go ahead and put our cover on and stow it away in the back of the vehicle. First thing we're going to do is open up the back compartment to gain access to our tail-light assemblies. more


Watch Video

12/30/2015 12:13:08 PM



Trailer Wiring Harness Installation - 2010 Pontiac G6- Video

Trailer Wiring Harness Installation - 2010 Pontiac G6

Today on our 2010 Pontiac G6, we're going install part number 118439 from Tow Ready. First thing we need to do is get the vehicle ready to install our wire harness. To do that, we'll go ahead and open up the trunk and we also have to remove the tail lights. To do that, we have to get behind the fasteners behind the carpet. We'll go ahead and remove this tab point and pull the carpet out of the way. We have to remove this nut here with a 10 millimeter socket and this one down here as well. Now we can go ahead and pull back our tail light. more


Watch Video

12/18/2014 5:08:16 PM



Trailer Wiring Harness Installation - 2003 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2003 Pontiac Vibe

Today on our 2003 Pontiac Vibe, we'll be install the Tow Ready T-One Vehicle Wiring Harness with 4-Pole Flat Connector, part number 118458. To begin our install we first open up the rear hatch. Our first step, we'll be removing the spare tire cargo cover. We'll unlock it and then lift it up the other way. Next, we'll remove the round knot that secures the cargo compartment above the spare tire. Once we remove the knot then we can remove the compartment. more


Watch Video

5/7/2014 10:59:40 AM



Trailer Wiring Harness Installation - 2008 Pontiac G6- Video

Trailer Wiring Harness Installation - 2008 Pontiac G6

Today on this 2008 Pontiac G6, were going to install part number 118439 from Tow Ready. All right to start off our install, we need to get inside a trunk area and remove the carpeting by the taillights. Once we get access to this taillight, we can go ahead and move the hardware forward taillights and then we can completely remove the taillights. Once we have our driver side taillight loose, well pull up on the tab located here so we can separate the electrical connector and then we can go ahead and remove the taillight. Were done with the driver side; lets repeat the same process over on the passenger side. Well go ahead and take our four pole wire and run down between the bumper cover and the body. more


Watch Video

2/15/2013 2:20:25 PM



Trailer Wiring Harness Installation - 2004 Pontiac Grand Prix- Video

Trailer Wiring Harness Installation - 2004 Pontiac Grand Prix

Today on this 2004 Pontiac Grand Prix were going to install part number 56076 from Curt. The first thing we need to do is go ahead and remove the rear trim panel at the threshold. We have to remove the interior liner to get access to hardware that holds the taillights in place so we can remove the taillights. These are the three fasteners we have to remove. Well pull the light away, and then well disconnect the wire harness. Well pull up on this tab right here and then pull it out. more


Watch Video

1/24/2013 1:12:48 AM



Trailer Wiring Harness Installation - 2005 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2005 Pontiac Vibe

Today on our 2005 Pontiac Vibe well be installing the Tow Ready T1 connector, part number 118458. First, well open up the rear cargo door, and then well need to open up the rear cargo tray spare tire area. With the tray cover up and out of the way, well go ahead and remove the spare tire tool tray. Well remove the center fastener and then we can just simply lift it up and set it out of the vehicle for reinstallation later. Next well go over to the access panel behind the drivers side taillight assembly. Removing the access door well expose the wiring to the rear taillight assembly. more


Watch Video

12/19/2012 2:29:29 PM



Trailer Wiring Harness Installation - 2007 Pontiac G6- Video

Trailer Wiring Harness Installation - 2007 Pontiac G6

Today on our 2007 Pontiac G6 well be installing the Tow Ready T1 Connector part number 118439. First, well need to access the rear cargo area. Well go ahead and open up the trunk and remove the cargo hooks here behind the drivers side taillight assembly. Then well go ahead and pull the carpeting back exposing the two 10-mm nuts that will need to be removed holding the taillight assembly in place. Now with those removed, we can go ahead and simply pop the taillight assembly free from its position and then remove the wiring connector going into the back of it. Next, well go ahead and repeat the same process on the passengers side. more


Watch Video

9/21/2012 2:04:43 PM



Trailer Wiring Harness Installation - 2005 Pontiac Grand Prix- Video

Trailer Wiring Harness Installation - 2005 Pontiac Grand Prix

Today on our 2005 Pontiac Grand Prix, we're going to install Part # 56076 from Curt. First thing we need to do is go ahead and open the trunk and remove the interior panels. On the passenger side of the threshold, there are two screws that need to be removed. We'll repeat this on the driver side then we can go ahead and remove the threshold. Next we're going to remove the wing nuts on both sides and loosen up the side carpet. Next we'll go ahead and remove the fasteners to attach our taillight so we can pull it apart. more


Watch Video

6/26/2012 8:50:57 AM



Trailer Wiring Harness Installation - 2001 Pontiac Montana- Video

Trailer Wiring Harness Installation - 2001 Pontiac Montana

Today on this 2001 Pontiac Montana, we're going to install part number 118355 from Tow Ready. First thing we need to do is pop up the back hatch, and remove the threshold at the bottom. Then we need to get the access behind the interior panel on the driver's side. Okay now, this is the location of the connection point right here. Now depending on the vehicle, some models have an open port that our T-connector will plug into, just one side and that's it. However, in this model the port is connected together, so disconnect it and install our T-connector. more


Watch Video

6/25/2012 4:10:02 PM



Trailer Wiring Harness Installation - 2006 Pontiac Montana- Video

Trailer Wiring Harness Installation - 2006 Pontiac Montana

Today in our 2006 Pontiac Montana, were going to install the toe ready T1 connector part number 118396. First well access the rear cargo area then were going to remove the two torch fit screws holding on the tail light for each sides, after we remove the hardware, well gently pull the tail light and assembly away from the body of the vehicle. As you can see this will allow us access to the tail light wiring harness. The tail like wiring connector will match the new T1 connector so well simply disconnect the manufactures wiring and plug the new T1 connector in line with the manufacturers. Once we get them snap into place, were going to go ahead and take the rest of our remaining wire and fit it down between the bumper cover and the sheet metal of the vehicle. Once we get all our wires fit underneath, just simply go ahead and reinstall the driver side tail light assembly. more


Watch Video

4/17/2012 11:24:02 AM



Trailer Wiring Harness Installation - 2008 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2008 Pontiac Vibe

Today on this 2008 Pointiac Vibe we're going to install part no 118458 from Tow Ready. So first thing we're going to do is go over to the back hatch and get down to the spare tire area. And we will remove this tray as well. Now we're going to remove interior panels behind the tail lights it will one on each side. Now take a wire harness with the read and yellow wires. We will run that to this openning here end up back here. more


Watch Video

3/9/2012 12:26:42 PM



Trailer Wiring Harness Installation - 2009 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2009 Pontiac Vibe

Today we're working on a 2009 Pontiac Vibe. We're going to install a Tow-Ready T1 Connector Part # 118460. First, we're going to access the rear cargo area of the vehicle. We're going to open up the tray door for the spare tire well. And then we'll just take that out, set that aside for reinstallation later. We need to remove the threshold here across the back.Take your gear, screwdriver or trim tool, get underneath the plastic, gently pry it up to free the fasteners from the sheet metal. more


Watch Video

1/4/2012 12:11:43 PM



Wiring Harness Installation- 2002 Pontiac Montana- Video

Wiring Harness Installation- 2002 Pontiac Montana

Today we are working on a 2002 Pontiac Montana. We will be installing a Tow Ready T-One connector, part number 118355. Our first step is going to be accessing the rear cargo area of the vehicle. We are going to remove the storage compartment door. Then remove these two plastic tabs here and pull back the trim panel to see if we can access our trailer plug from here. :22 more


Watch Video

9/12/2011 1:31:47 PM



Trailer Wiring Harness Installation - 2006 Pontiac Vibe- Video

Trailer Wiring Harness Installation - 2006 Pontiac Vibe

Today we are working on a 2006 Pontiac Vibe. We will be installing Tow Ready T-one connector, part number 118458. First we will access the rear cargo area of the vehicle. Then we are going to raise up the cargo hold for the spare tire. We will actually remove the cover over the spare tire which also holds the spare tire tools. We will go ahead and set that aside. Once we do that, we can go ahead and open this access door. We will go ahead and set that off to the side. Next we are going to take the red and brown wire and the yellow and white wire here, both connecters. We will feed them through the access hole here and bring them out though our access panel up here. Now I am going to set those aside for a second. 0:49 more


Watch Video

7/14/2011 3:41:52 PM



Trailer Wiring Harness Installation - 2006 Pontiac Montana- Video

Trailer Wiring Harness Installation - 2006 Pontiac Montana

Today on this 2006 Pontiac Montana we are going to be installing wiring harness part number 118396. We are at the rear of the vehicle, with the cargo door open, and we want to go ahead and locate the port that our wiring harness is going to be plugging into. The ports are located directly behind the taillight on both the driver and passenger side. So the first thing that we want to go ahead and do is remove both taillight assemblies. Holding the taillight in place on the inboard side are two torque headed bolts. We need to go ahead and take those out. 0:38 more


Watch Video

8/4/2010 7:39:24 AM



Trailer Wiring Harness Installation- 1999 Pontiac Montana- Video

Trailer Wiring Harness Installation- 1999 Pontiac Montana

Today on this 1999 Pontiac Montana we are going to install part number 118355 from Tow Ready. This is our T-1 wiring harness. The first thing we need to do is get in the back of the vehicle and get behind the access panel on the driver side. Pull out this panel right here, there is this plastic panel behind that, this is the part we are going to have to remove. Towards the back we should find our connector that will match up. :31 more


Watch Video

7/26/2010 11:57:12 AM



Trailer Wiring Harness Installation - 2007 Pontiac Torrent- Video

Trailer Wiring Harness Installation - 2007 Pontiac Torrent

Today on this 2007 Pontiac Torrent we are going to be installing wiring harness part number 118432. We are in the rear cargo area of our Torrent and we want to locate the port that we are going to be plugging our wiring harness into. This port is located actually in our jack storage compartment connected to the bottom floor board. The first thing we need to do is get inside here and remove our jack. With that removed if you look down at the bottom of the floor board you will see an open ended port which we are going to be plugging our wiring harness into. 00:38 more


Watch Video

6/22/2010 10:59:37 AM



Trailer Wiring Harness Installation - 2009 Pontiac Torrent- Video

Trailer Wiring Harness Installation - 2009 Pontiac Torrent

Today on this 2009 Pontiac Torrent we are going to install part number 118432 from Tow Ready. First we will show you where the T Connector plugs in at, it is actually in the jack storage compartment down toward the bottom at the floor. So to get access to it we are going to do is take off this panel and remove the jack tools themselves. more


Watch Video

8/31/2009 12:27:45 PM



Trailer Wiring Harness Installation - 2006 Pontiac Torrent- Video

Trailer Wiring Harness Installation - 2006 Pontiac Torrent

Today we are going to install a T-1 wiring connector by Tow Ready on a 2006 Pontiac Torrent, part number 118391. To begin our install, we are going to remove the side panel it just snaps out. Next we have to take out the jack. Once the jack is removed we want to look for the wiring harness. As you can see, the wiring harness is just electrical taped down in the bottom of the cavity of the frame, and once you get it freed up, all you need to do is just connect the wiring harness to it and ground it, and then you are good to go. more


Watch Video

2/25/2009 10:15:40 AM



  1