Saturn Custom Fit Vehicle Wiring Installation And Review Videos

  

Trailer Wiring Harness Installation - 2007 Saturn Aura- Video

Trailer Wiring Harness Installation - 2007 Saturn Aura

Today on our 2007 Saturn Aura we'll be installing the Tow Ready Custom Fit Wiring Harness, part number 118423. We will start by opening the trunk. We'll then remove the threshold trim. After popping the threshold trim loose we'll go ahead and remove these two cargo nut screws. With those out of the way we'll go ahead and peel back the trunk liner. With the trunk liner out of the way you can see these three thumb screws that we'll remove to loosen up the taillight assembly. Once the taillight has been pulled back and out of the way we'll go ahead and disconnect the wiring from the taillight. more


Watch Video

1/23/2015 7:15:05 AM



Trailer Wiring Harness Installation - 2009 Saturn Vue- Video

Trailer Wiring Harness Installation - 2009 Saturn Vue

Today on this 2009 Saturn View we'll be installing a Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part number C56026. We'll glue the fastener at the bottom of the inner cargo pocket. Using a flat blade screwdriver go ahead and twist out the plastic cap nut. Once we have all of the fasteners out of the corner panel we'll then go ahead and remove the corner pocket. The corner pocket has a push pin fastener in the bottom, so we'll get underneath it and gently pull it up until it releases. To remove the corner pocket I'm just using a plastic pry tool. more


Watch Video

12/22/2014 1:24:06 PM



Trailer Wiring Harness Installation - 2009 Saturn Vue- Video

Trailer Wiring Harness Installation - 2009 Saturn Vue

Today on our 2009 Saturn Vue will be installing Tow Ready T-One Connector, part number 118443. Now to begin our installation, we'll need to open the rear left gate, remove the threshold plate, the trunk floor panels and the spare tire tray from the vehicle. Now on the driver side of the vehicle, we need to remove the fasteners that hold the black Styrofoam tray where we can then carefully pry the black tray out from the underneath the side panel. We'll next locate the plastic side pocket inside the driver's side trim panel. We also need to remove the screw here, slowly pull up on the tray until it pops out of the panel. This will expose our wiring that are T-One Connector will tap. more


Watch Video

11/21/2012 11:46:41 AM



Trailer Wiring Harness Installation - 2003 Saturn Vue- Video

Trailer Wiring Harness Installation - 2003 Saturn Vue

Today on our 2003 Saturn Vue, well be installing the Tow Ready T1 Connector, part number 118418. Before we begin the installation, weve gone ahead and raised the vehicle and removed the rear wheels. Now, were going to open up the rear cargo door and remove the two fasteners securing the passengers side tail light assembly. Once we have the assembly loose, well go ahead and unlock the wiring connector that runs to the assembly and disconnect the wiring. Repeat the same process on the passengers side. Well now move to inner wheel wells. more


Watch Video

5/4/2012 10:15:58 AM



Trailer Wiring Harness Installation - 2008 Saturn Outlook- Video

Trailer Wiring Harness Installation - 2008 Saturn Outlook

Today on this 2008 Saturn Outlook, were going to install part number 118434 from Tow Ready. First thing we do is open the back hatch and move the two tail lights. Remove the tail lights. We got these two covers removed so to access through the hardware. Now, disconnect your hardware. Theres a little latch on the inside edge right here. more


Watch Video

2/10/2012 2:29:50 PM



Trailer Wiring Harness Installation - 2005 Saturn Relay- Video

Trailer Wiring Harness Installation - 2005 Saturn Relay

Today, on this 2005 Saturn Relay, were going to install part number 118396 from Tow Ready.First thing we need to do is go ahead and open the back hatch, and remove the taillights. Now this wire harness, well disconnect it right here, push down this tab, we can pull it apart. Passenger side done, lets go over to driver side and repeat same process.Now I can start installing the wire harness. Well take our four-pole, take it behind the bumper cover and eventually run it at the bottom. Now well take our half of the green and white wire, well run that down as well. And well take our harness the yellow wire, well plug that back into the factory wire harness. more


Watch Video

2/6/2012 11:35:04 AM



Trailer Wiring Harness Installation - 2007 Saturn Outlook- Video

Trailer Wiring Harness Installation - 2007 Saturn Outlook

Today on this 2007 Saturn Outlook we are going to install part number 118434 from Tow Ready. The first thing we need to do is open up the back hatch of the vehicle, that is where our wiring connections will be at. There are two attachment points behind these two little plastic covers so we just need to pop those off and get behind the screws behind them. Pull the light gently at an angle away from the vehicle and this is our connection point. This is going to plug in between these two halves of the connection point. We are going to push down this little lever right here and it pops right apart. 00:35 more


Watch Video

10/11/2010 10:19:45 AM



Trailer Wiring Harness Installation- 2009 Saturn Outlook- Video

Trailer Wiring Harness Installation- 2009 Saturn Outlook

Today on this 2009 Saturn Outlook we are going to install 118434 from Tow Ready. The first thing we need to do is open up the rear hatch and get access to the tail lights. Now we need to remove the tail light itself, so we are going to remove these two covers, and the screws are behind the covers. Then we can pop off the light. Then we can disconnect the light from the vehicle. This latch right here will pull down. We have the driver side tail light removed, lets go to the passenger side and repeat the same process. :36 more


Watch Video

7/27/2010 8:10:49 AM



Trailer Wiring Harness Installation - 2006 Saturn Vue- Video

Trailer Wiring Harness Installation - 2006 Saturn Vue

Today we are going to install part number 118418 from Tow Ready on our 2006 Saturn Vue. The general layout of this wire harness is that the connections are behind the tail lights, route the wires underneath the vehicle, and the wires will be stored outside the vehicle when we are done. To start off, we will take off the tail lights we will lift the hatch to get to those. All right, and here is our connection point right here. So let us pull this latch out and pull it apart. And repeat for the passengers side. All right, next we need to loosen this section of quarter-panel here to give us some room to run our connectors and put our black box for the T-harness hidden back up inside of here. What we are going to do is take out this nut here and this nut here, and that will give us enough wiggle room to pull the panel off just a little bit. more


Watch Video

3/31/2009 9:15:08 AM



  1