Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
(218 reviews)
Price: $204.32
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
Item # HSSF
Retail:$219.77
Our Price: $204.32
You Save: $15.45
This item qualifies for Free Shipping
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (218)
- Q & A (0)
- Photos
- Used (2)
Brophy Camper Tie-Downs - HSSF
- Front and Rear Tie-Downs
- Brophy
- Bed-Mounted
- Powder Coated Steel
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.
Features:
- Creates attachment points for securing your camper to your truck bed
- Wide clamps provide superior holding strength
- Turnbuckles (sold separately) required to attach camper to tie-downs
- Protects your truck's paint with neoprene pads attached to the brackets
- Resists corrosion and rust with black powder coated steel
- Clamps securely onto your bed rails - no drilling required
- Includes 4 camper tie-downs with clamp plates, 12 neoprene pads, and installation hardware
- Made in the USA
Specs:
- Application: for exact fits, enter in your vehicle's year/make/model above
- Minimum 2" needed between sidewall and lip of bed rail
- Not compatible with drop-in bed liners, aftermarket bed rails, double-walled beds, or side-step beds
- Dimensions: see diagrams below
- 1-Year limited warranty
No-Drill Installation
These clamp-on tie-downs install quickly and easily, with no drilling or modification to your truck required. Because they're mounted in the bed instead of on the frame or body of your truck, you don't need any kind of fancy mechanical background to get this job done. You just need to slide the hold downs over the rails of your truck and clamp them down with the included T-bars and hex bolts.
The fact that they simply clamp on means that you can remove these tie-downs when you're not hauling your camper, leaving no trace. Use the provided neoprene pads on the T-bolts and tie-downs where they make contact with your truck to make sure no scratches or dents will be left behind either.
It's important that the tie-downs on your truck line up with the anchors on your camper at the correct angle to ensure a secure hold. Ideally the tie-downs should be on the outside of your camper's anchor points, but they can be on the inside as well, just as long as they're not lined up with each other.
Securing your Camper
To secure your camper to your truck, you'll also need a tie-down hardware package consisting of turnbuckles, S-hooks, and chains (TDHP - sold separately). This hardware attaches the anchors on your camper to the tie-downs on your truck to keep your camper safely mounted. Once you tighten the turnbuckles to the correct level of tension (not too tight!), you'll be good to hit the road.
HSSF CR Brophy Truck Camper Tie Downs for Slide In Truck Camper - Camper Hold Down - No Drill Tie Down - 4 Pack
Installation Details
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4 - HSSF
Average Customer Rating: 4.6 out of 5 stars (218 Customer Reviews)
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.by: TheAvionNomad01/18/2024
I used these to mount a vintage 1970 Avion C-11 to a 1993 D250. They worked great and were much stronger than I expected - and it was a huge cost savings (and a much more attractive look) than some of the frame mounted options of more than $1000. There were some oddities that I noticed. It was impossible to mount them exactly the way the instructions suggested because of where on the wings near the cab,. The brackets also could not stay on with the camper unloaded because they would hit the jack mounts, meaning they had to me bolted in after the camper was in the truck but before lowering the jacks, making the access to the bolts a frustrating 'feel for it' experience.I'f suggest the manufacturer secure the bolt so that you don't need to hold both sides when tightening/loosening, and also refine it to need less turns to do so. It took me 2 hours to mount the first time, and not much less when removing them with the limited access. The pads also came off in the first use.
I gave it a 5 star because I realize there are limited options for older campers and anything universal is going to have issues with some thing - so that's just my input and experience. Overall pretty reasonable for the price and functionality.
by: Pat03/20/2023
The product was shipped extremely quickly, it arrived 3 days after I ordered them. As far as the product goes I was extremely pleased that they were as easy to install as the product video showed them to be. I had been looking for
a tie down system that would work for my 2018 Ford since I purchased my camper in 2020 and after much research I found these at etrailer. One word of advice is that if your camper has a shower or other design that allows the camper to extend across the bed behind the wheel wells, either move the rear tie downs forward or shorten the leveling stud before you attempt to load your camper. On mine it turned out that once the tie downs were placed and attached I had to cut off about 3 inches of the threads.
Other than that it was an easy install although the bolts that attach the tie downs to the under lip clamp are a challenge to install but take your time and they will go on. I will post an update once I have been on the road for a few trip and see how they are working.
Thank you etrailer for your super fast shipping and online product videos.
by: Jeff Smith10/22/2023
These tie downs work great. It holds my 3k lb Cabover camper in place without issues. And I live in my camper, so not losing my home is very important to me!!
by: Ed B.05/21/2019
Purchased the Brophy camper tie down set of four for the Palomino truck camper I just purchased. These are my second set as the first set were sold with my Hallmark camper. Easy to install and hold the camper in the truck with no worries.
by: James 05/20/2024
Ordered these for new camper. Very easy to install and does the job without the high cost of frame mount.
by: Shelly12/13/2023
The products arrived on the time scale as stated. The packaging did not hold up and the box with the metal tie downs was broken open. There was too much weight for the box and it just split open. Not sure if anything is missing. Packaging of items that are heavy should be more secure and sturdy.
Jenny N.
12/14/2023
Oh no! I will have our Customer Service team reach out to you. If anything is missing we can take care of it.
by: Allen.08/22/2022
These wont work for my truck and camper. The box on a 2018 gmc 2500 short bed does not lend well to placement of these in order to get the correct geometry i needed for the tie-down points on my Palomino maverick 6601. I had high hopews of not having to buy the frame mounts, but i will have to.
Mike L.
8/31/2022
The HSSF tie downs have specific fit parameters as mentioned in the product specifications above: External bed rail width cannot exceed 5-12 Requires at least 2 of space beneath lip of bed rail Not compatible with -in bed liners, bed rails, double-walled beds, or side-step beds
Allen.
8/23/2023
In response to the etrailer comment response, they fit on the bed fine, with plenty of clearance and would work for a smaller camper. they just did not fit in the right spots for my truckcamper combo.
by: Ron W07/02/2016
As far as I'm concerned these are junk. Wasted my money. Do not mount in proper location on a 2011 Chevy Silverado 6.5' Bed. Because of the design of the bed rail the mounts cannot be installed in the proper locations for securing camper. The photos show the maximum forward and back that these can be mounted. Not at all made for the 6.5 foot bed 2007 or later Siverado. The Black Powder Coated Steel isn't that great either. Paint missing, dinged up from storage and shipping probably.
by: . George01/03/2024
The tie downs are great no problems.Very easy to install.I keep them on my truck all year long Thank you
by: Terry08/08/2023
Order arrived quickly, priced ok. Box was broken open by shipper NS the 4 T-bolsts bolts ere missing. Etrailer shipped ou the missing parts a few days later, but in the meantime I fashioned t-bolts I could use for my trip. Many customer comments on this camper Brophy tie-down match my experience. Etrailer follow up was great, but surely must be aware that their packing is sub-standard. Perhaps zip-tying the T-bolts to larger pieces would eliminate the loss even in case of breakage. Functionally the tie-dows were easy to install and seem quite adequate for off-road use of my in-bed camper. Will continue to use etrailer because of their excellent customer service.
by: Mike S05/23/2020
These Brophy tie downs have worked great over the past year. I leave the camper on the truck and it is my daily driver as well as RV. The camper weighs in at 1500 dry and about 2000 loaded. I do not do any radical 4x4 but I have taken some backwoods off road logging trails.
by: captkirk02/15/2021
These tie-downs worked awesome for our pop up camper on our 1998 F150. Super snug, haven't loosened up or moved on the truck, camper hasn't budged either. I was leary at first not having the camper tied to the frame but now I have total faith in these tie downs.
by: Bing09/23/2019
I received this tie downs on July, and first used it yesterday.
My Camper ‘s dry weight is about 1600 lb, and the products are good for my truck camper.
The problem was the position where tie downs were fitted on my truck. I tried several times to fitted tie downs to my truck.
by: Patrick04/02/2020
These things are solid although i put duck tape on the T pads....installed 2014 Chevy Silverado 6.5 ft bed for 1200lb Starcraft.
Patrick
4/6/2021
Still have not moved! Great design and cost savings.
by: Brent 08/08/2019
I bought these for our brand new 2019 GMC Sierra 1/2 ton because no custom options were available. I was happy that they were easy to install, and look great. I’ve used them in the past and have been happy with how they hold campers. Sure I’d rather have custom mounts from the frame, but for the price and because these are my only option that’s what I got. These will work just fine, and I like that I can swap these out on trucks.
The one thing I wish was different was that the threaded T handle portion would have a longer option. I had to fancy up a 2”x6” to run inside the side of my p/u bed so they would touch something.
As always another great shopping experience with etrailer. They haven’t let me down yet. Especially Lori, what a great customer service rep.
by: Matt04/14/2015
These camper hold-downs appear to be manufactured from good steel stock and should do the job nicely. I did have one piece that was slightly damaged but was not caught when packaged (the damage was not due to shipping). I was able to take a hammer to the bent steel and straighten it sufficiently to use the part. It was a little disappointing however, and should have been caught prior to shipping.
Overall I am pleased with the quality and price
by: Regan06/25/2019
Using on 2013 Ford F150 for a smaller cabover. Great quality product, shipped fast, works great. Had to turn bolts around to clear inside of bed. Held camper solidly over rough trails!
by: Bryce05/10/2022
Fits well on a First Gen Tundra. I was extremely unsure about fitment for my truck but they work great! Install only takes 5-10 minutes. I would definitely recommend. Steel is quite thick and seems very strong.
by: John05/25/2020
Easy to install and have done what’s expected. Keep the camper in place!!
by: JAMES K09/24/2012
ORDER ON TUESDAY RECIEVED ON FRIDAY NOON SAME WEEK ONLY PROBLEM WAS 4 7/ 16 NUT WERE 4 1/2 NUT HAD TO BUY 4 NUTS OTHER THEN THAT I WOULD BUY OFF ETRAILER AGAIN VERY GOOD SERVICE
by: Chuck11/13/2012
Found easy to install, I placed lock washers on the 8 3/8" bolts. Sold at Menards for 89 cents (pkg of 8) not in kit. Placement was a little restrictive with dealer installed bed liner. Takes 30 minutes to install all 4. Great buy.
by: Neil08/04/2021
Arrived on a rainy day with the box falling apart. Too much heavy steel to be loosely packed. Fortunately, the hardware bag was still there. Some bare metal showing. I had some emails with MacKenzie B. and they were responsive and without asking they offered me a 5% refund for the damage. After my first trip, they performed well on some very bumpy roads. Held strong and didn't move. I did have to re-adjust the lower standoffs after the first week. Taking them on/off is frustrating because the 2 nuts are in the small gap behind the clamp against the inner bed wall. Too tight for all but an open end wrench. 1/6 turn times too many fumbling tries, arg! Also, I was nervous not having a locking feature (lock washer, locknut, etc). I bought 8 locknuts (pinch type) and welded them to the inner plate. Then bought 8 round head hex bolts (grade 8). So now I can install easily with an Allen socket. See pictures. Recommend eTrailer consider this modification.
Neil
8/5/2022
After my mount bolt mod, Ive used these multiple times and they are working great! Very stout and no visible marks on my F250 bed.
by: Dayton12/15/2023
Awesome customer service my new fav pl ace
by: Jason S.06/05/2019
These tie downs were a great budget solution in leu of a permanent installation of my camper shell and/or frame mounted tie downs. Aside from needing to plan their placement (they can hang in front of the gas cap if you don't plan it right the first time around... no, I didn't accidentally block my gas cap... maybe I did) and take into consideration they also need a little bit of internal clearance as well, they work just fine. I haven't noticed any cargo shifting nor warping of the truck bed around where they are installed. My camper shell is under 1K lbs and it holds just fine.
Jason S.
6/8/2020
A year later & they still hold strong.
by: Dan N.08/23/2013
The product is made from very good stock. They seem to be well built . I had a bit of a problem installing on my truck ,and ended up putting the bolts on the angled support rack in backwards according to the video , which I watched after . The tie downs have not been camper tested yet and I am excited to try them out!
Dan N.
2/21/2015
The tie downs have worked fine for me . I have a smaller pop up pick up camper . I am sure for lighter campers they would work fine . I have seen the product work with two on the front as tie downs and then in the back , the button type bumper mounts in the back . This may be a good way to go for more stability on a larger camper. JMHO
25
218
Show More Reviews
See what our Experts say about this Brophy Camper Tie-Downs
- Recommended Truck Bed Camper Tie Downs for 2017 Nissan Titan XD 8' BedI do have an option for you but there are no custom frame mounted truck bed camper tie-down brackets for a 2017 Nissan Titan XD with an 8' bed. Therefore, our only options are universal bed mounted camper tie-down brackets like the Brophy Clamp On Camper Tie-Downs part # HSSF which you can then secure your camper to using the Brophy Basic Turnbuckles part # TDHP.
view full answer... - Camper Tie Down Recommendation for a 1988 Chevy K2500The camper tie downs, # TDSF, will not work with 1988 and newer Chevy/GMC trucks. If your truck is not a step side, does not have a double-wall bed, and is not a dually, you can use # HSSF with hardware package # TDHP. I have included some pictures that show how the tie downs install.
view full answer...
- Brophy Camper Tie Downs Compatibility With A 2020 Ford F-350 Super Duty With Factory Spray Bed LinerAs long as your external bed rail width does not exceed 5-1/2" and you have at least 2" of space beneath the lip of bed rail the Brophy Clamp On Camper Tie-Downs # HSSF will be a fine fit for your 2020 Ford F-350 Super Duty with a factory spray bed liner.
view full answer... - Which Brophy Camper Tie Downs Fit 2001 Toyota TundraFor tie-downs that will work in your 2001 Toyota Tundra you will want the Brophy Clamp On Camper Tie-Downs # HSSF. Brophy has told us in the past that the # HSWB was intended for domestic trucks. These tie-downs are compatible with the turnbuckles # TDHP that you'd need to complete your camper tie down setup for your truck. This provides the connection from the tie down to the camper. I attached a review video for more info as well.
view full answer...
- Does Brophy Camper Tie Downs # HSSF Fit 2018 Ford F-150 6-1/2 foot BedYes the Brophy Camper Tie Downs part # HSSF do fit your 2018 Ford F-150 with a 6-1/2 foot camper.
view full answer... - Recommended Universal Camper Tie-Downs for 1979 Dodge PickupThe Brophy Camper Hold Downs, part # HSSF, which you reference, are a universal fit item and will work on most full-sized trucks, so they should work well with your pickup. Some dual rear wheel beds and bed liners that block the top edge of the side rails can cause a problem with the installation of these hold downs. These hold downs wrap around the bed rails and are mounted inside the bed under the side rails. These tie downs do not have a weight capacity limit and will work for any camper...
view full answer...
- Brophy Camper Tie Downs that Fit 2016 Ford F-150 Short BedAccording to my contact at CR Brophy Machine Works, their # HSSF truck bed camper tie-downs are compatible with the 2016 Ford F150. You'd also need the hardware package, part # TDHP, which includes the hooks, turnbuckles and lengths of chain to connect the tie downs to the camper. The # HSAB will not fit your truck.
view full answer... - Will the Brophy Camper Hold Downs # HSSF Fit on a 2012 Chevrolet Silverado 2500HD Long BedThe Brophy Camper Hold Downs, # HSSF, are a universal fit item that were designed to fit many different trucks, including your 2012 Chevrolet Silverado 2500HD Long Bed. We have not had the chance to test fit these hold downs on a 2012 Chevrolet Silverado 2500HD long bed at our facility yet, but we have successfully installed these hold downs on previous generations of GM trucks. We have also had customers install these hold downs on GM trucks that have the same body style as yours without...
view full answer...
- Will Brophy Camper Hold-Downs Part # HSSF Fit 2001 GMC Sierra and Damage Truck Bed RailThe Brophy Camper Hold Down, part # HSSF, is a universal-fit item that will work in the vast majority of pickups except those with step-side beds; it will also not fit some double-wall or dually beds. It will work with your 2001 GMC Sierra with 8-foot bed. Installation instructions are included. The HSSF is a no-drill product that clamps to your bed rails. Included are protective neoprene pads for the clamps to safeguard your vehicle paint. Brophy also offers a similar product, # HSAB,...
view full answer... - Camper Tie Down Recommendation for a 2014 Ram 1500 with Running BoardsI have a set of camper tie downs that will fit your 2014 Ram 1500, but they attach at the stake pockets of the bed and not the frame like the Torklifts do. There is no Torklift option for your truck if it has running boards. The Brophy Camper Tie Down, part # HSSF is a universal fit item and will work on your 2014 Dodge Ram 1500. The Brophy Tie Down mounts over the sidewall of the truck bed. The recommended hardware kit to install part # HSSF is Camper Tie Down Hardware Package, part...
view full answer... - Will Brophy Clamp On Camper Tie-Downs # HSSF Fit a 2014 Nissan Titan King Cab?The Brophy Clamp On Camper Tie-Downs # HSSF are a great option for securing your camper to your truck. To make sure these tie-downs will fit your 2014 Nissan Titan, you need to take some measurements on your truck. First, measure the width of the top rails on your truck bed to make sure they are less than 5-1/2". Next, make sure you have at least 2" of space beneath the lip of the bed rail. Note that these are not compatible with drop-in bed liners, plastic bed rails, double-walled beds,...
view full answer... - Truck Bed Camper Tie Down Recommendation for a 2004 Ford F-150 with 6.5 ft Short BedThe Stake Pocket Camper Tie Downs, # TDSF, would be a good choice for your 2004 F-150 with 6.5 ft. Short bed, as long as your camper is not over 8 feet long. A better option, or if your truck camper is longer than 8 feet, would be to use the over the rail Camper Hold Downs, # HSSF. I installed a set of these and took some photos showing how they mount and how the pressure is applied when attached with the Camper Tie Down Hardware, # TDHP. For the ultimate tie down performance, frame mounted...
view full answer...
- Camper Tie-Down Recommendation for 2005 Dodge Ram 2500We do offer Brophy tiedowns that will fit your 2005 Dodge Ram 2500 as long as it does not have a stepside bed or dual rear wheels. The Brophy tiedowns that will work for your application is part # HSSF. The hardware kit you would need to attach the tie-downs to the camper is the part # TDHP.
view full answer... - Truck Bed Camper Tie-Downs for 2007 2500Chev Crew Classic According to my contact at CR Brophy, the # TDSF stake pocket camper tie down isn't compatible with your truck. The # HSSF clamp style tie down will work as long as your truck bed has two inches of available space under the truck bed sidewall as shown in the provided diagram. You'd also need the hardware package, part # TDHP which includes the chains, turnbuckles and hooks to connect the tie-downs and the camper.
view full answer...
- Manual Jacks to Lift a 2008 Bronco Polarino Truck Bed CamperBrophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 Item # CJ74 will work great with your 1,600 pound truck bed camper. Just make sure that the 67 inch maximum lift height is enough to get the camper into the truck bed. The brackets that lift the camper are 21-1/2 inches long so when properly placed at the center of gravity on the camper it will be balanced. It is recommended to have 2 people when operating the jacks so they lift evenly. For tie downs we have custom options...
view full answer...
- Does the Brophy Clamp # HSSF Fit A 2018 F150 Crewcab 5.5 BedYes, the Brophy Clamp On Camper Tie-Downs # HSSF will work just fine with your 2018 Ford F-150. The Brophy Tie-Downs are easy to install and remove and require no drilling for installation. The Brophy Tie Down # HSBP will work for you if you have the required 5.5 inches of maximum width and have the 2 inches of space under the bed rail. In order to secure the truck bed camper to these tie-downs you will also need the Brophy Basic Turnbuckles # TDHP. If you have any further questions please...
view full answer... - Will TDSF Camper Tie Downs Fit 1995 Dodge Ram 2500 Long BedYes, the stake pocket camper tie downs, # TDSF, will work on the 1995 Dodge Ram 2500, as long as the overall length of the camper you are using them with is 8 feet long or less, this measurement includes the overhang over the cab of the truck. You will need to drill one 11/32 inch hole and two 7/32 inch holes for this installation, and there are spacer tabs on the tie downs that may need to be pried off for a proper fit in your stake pockets. If your truck campers overall length is longer...
view full answer... - Tie Downs for my 2006 GMC Sierra Extended Cab and Palamino In-Bed CamperAs long as the bed in your 2006 GMC Sierra is not a step-side, double wall or a dually, then the Camper Hold Downs, # HSSF, will work well for you. Take a look at the helpful link I have included to see how these tie downs install. These tie-downs wrap around the bed and do not fit in the stake pockets. Stake pocket mounted tie downs that will fit your truck are not available. With these tie-downs, I recommend the camper tie down hardware package, # TDHP.
view full answer... - Compatibility of Brophy # HSSF Camper Tie-Downs with 1995 Chevy C/K 2500According to my Brophy representative, their # HSSF truck bed camper tie downs are compatible with the bed of your 1995 Chevy 2500. If you have the plastic drop-in bed liner, you'll need to trim it so the tie downs clamp directly to the underside of the bed rail. The # TDHP hardware package is also recommended. The linked video will provide you an idea of how the tie-downs install.
view full answer... - Difference Between The Brophy Camper Tie-Downs HSAB And HSSF The Brophy # HSAB and # HSSF are essentially the same thing with the exception that the # HSAB has a small bend in it to make connecting to your turnbuckles easier. If you're still needing turnbuckles you can use part # TDHP.
view full answer... - Comparing Brophy Truck Bed Camper Tie DownsOn the ends of the Brophy tie downs # HSAB where you would tie off the camper the tip is turn up to be parallel with the ground. The angled design allows more clearance between hold-downs and truck fenders.On # HSSF the tips are not turn up and are at about a 45 degree angle. For either kit I also recommend the associated hardware package # TDHP.
view full answer...
- Best Fitting Brophy Camper Tie-Downs For 2004 GMC Sierra 2500 HD Duramax I spoke with Brophy and they stated the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item # HSSF would be the best fit for your 2004 GMC Sierra 2500HD Duramax. You'll also want some turnbuckles, which I recommend the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs - 3,000lbs - Qty 4 Item # TDHP.
view full answer... - Truck Bed Tie Downs for a 1995 Ford F-150 and Light Weight 8-1/2 Foot CamperFor your 1995 Ford F-150 and camper, I recommend the Camper Hold Downs, # HSSF. The hold downs do not fit in the stake pockets but wrap around the bed rails and are mounted inside the bed. There is no weight capacity rating on the hold downs and the will work for any camper size that is properly sized for your vehicle. I also recommend the Camper Tie Down Hardware Package, # TDHP, which has a weight capacity of 3,000 pounds.
view full answer... - Do Brophy Camper Tie Downs fit a 2021 Nissan Titan XDYes, the Brophy Clamp On Camper Tie-Downs # HSSF will fit on your 2021 Nissan Titan XD as long as your external bed rails do not exceed 5-1/2", you don't have a drop in bed liner, plastic bed rails, double-walled beds, or side-step beds. You shouldn't need to remove your factory bed rails unless they are raised rails. You will also need the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs # TDHP to secure your camper to the truck bed.
view full answer...
Do you have a question about this Camper Tie-Down?
Used Items Available
Condition: Installed
Notes: Item has been installed/test fit.
Condition: Surface Scratches
Notes: Parts are scratched up, seems to be some signs of instalation, otherwise fine.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Expert Research:
Sarah H
Video Edited:
Zack K
Video by:
Patrick B
Installed by:
Matthew K
Installed by:
Cole B
Updated by:
Rachael H
Updated by:
Amanda M
Updated by:
Manda E
Updated by:
Amanda K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Ed B.
5/22/2020
No problems. Would buy again. Very easy to take on and off the truck.