To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
Specs:
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights on both the driver's side and passenger's side. You will need to remove the rear threshold panel and some interior lining to access this harness. Once you've plugged in the T-connector, run the hot lead with the attached fuse holder up to your car battery. Connect the fuse holder to the positive terminal on the battery and insert the provided fuse.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to review part number 118602. This is the Tow-Ready T1 vehicle wiring harness with the four pole flat trailer connector. This is a custom fit wiring harness. It is designed to fit the 2013 and 2014 Chevrolet Malibu LTZ models, except the Canadian models. This will provide a four-way flat trailer connector at the back of your vehicle to power your trailer's signal lights. It comes with all the hardware pictured here.
It connects quickly and easily. Basically this will plug into your vehicle's wiring harness, which is located inside your trunk behind the tail lights on both the driver's and the passenger side. Basically you will need to remove the rear threshold panel and some interior lining to access this harness. Basically what you would do is once you plug in the "T" connectors, you have these, the yellow, this connector, with the "T" connector on it with the yellow wires will go to your driver's side. You'd unplug the connectors on the back of your tail lights, plug this in line to that connection. Right here, the one that is green and red, the green would go over to the passenger side.
Same way, you would unplug the connector on the tail light, the back of the tail light, plug this in line to it. What you would end up also having to do, is there is a white wire, this is the ground wire, with the eyelet on the end coming out of the module light, this would have be grounded to a nice clean unpainted surface. They include a self-tapping screw to do that. The four-way, you can see, is coming out and then the other exposed wire is this red wire. This red wire would be the power wire.
This wire you would have to run from the back of your car to the front of the car where the battery is located and this will supply the power to the module light. The way they do that, this will ensure that your vehicle's wiring matches that of your trailer and this powered module connect directly to the battery will help avoid overloading your vehicle's electrical system. Basically, what you would do, is take this wire they include, this length of wire, and on one end, and these butt connectors, you would connect it to this red power wire with the butt connector, run it to the front, and with this other end, you would hook one end to this in-line fuse holder before you attach it to the battery. Use the butt connector, the other one to connect that, and then once you have done that, you have this one here. You would take the eyelet connector, put it on, and that would connect to the positive post of your battery. Then what you would need to do is take the included ten amp fuse, plug it into your fuse holder, and then you can put the cover over it and then it would be all ready to go. Now they also include this double sticky tape pad and that would be used to attach this module light to a flat surface on the rear of your vehicle.
It also includes some cable ties to tie up any loose line that might be dangling down or keep it away from any hot places and it does come with the instructions. It does come with a one-year limited warranty and that should do it for the review on part number 118602, the Tow-Ready T1 vehicle wiring harness with the four pole flat trailer connector. .
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.